Risk Of Injury - Parkside PKS 1500 B3 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

9.5 Precision adjustment of the stop for mitre cut
45° (fig. 1/2/3/6/7/8)
• No stop angle included.
• Lower the machine head (4) and secure it using the locking
bolt (25).
• Fix the rotary table (13) in the 0° position.
Important. For mitre cuts, the adjustable stop rail (8a) must
be fixed at the inner position.
• Open the set screw (8b) for the moveable stop rail (8a) and
push the moveable stop rail (8a) outwards.
• The adjustable stop rail (8a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (8a) and the saw blade (6) amounts to a maximum
of 8 mm.
• Before making a cut, check that the stop rail (8a) and the
saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Loosen the locking screw (23) and use the handle (3) to
angle the machine head (4) 45° to the left.
• 45° - position angle stop (B) between the saw blade (6) and
rotary table (13).
• Loosen the locknut (22a) and adjust the adjustment screw
(22) until the angle between the saw blade (6) and the ro-
tary table (13) is precisely 45°.
• Re-tighten the locknut (22a).
• Subsequently check the position of the angle indicator. If
necessary, loosen the pointer (28) using a Philips screwdriv-
er, set to position 45° on the angle scale (27) and re-tighten
the retaining screw.
9.6 Mitre cut 0°- 45° and turntable 0° (fig. 1/2/3/6)
The cross cut mitre saw can be used to make mitre cuts of 0° -
45° in relation to the work face.
Important. For mitre cuts, the adjustable stop rail
(8a) must be fixed at the inner position.
• Open the set screw (8b) for the moveable stop rail (8a) and
push the moveable stop rail (8a) outwards.
• The adjustable stop rail (8a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (8a) and the saw blade (6) amounts to a maximum
of 8 mm.
• Before making a cut, check that the stop rail (8a) and the
saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (13) in the 0° position.
• Loosen the locking screw (23) and use the handle (3) to
angle the machine head (4) to the left, until the pointer (28)
indicates the desired angle measurement on the scale (27).
• Re-tighten the locking screw (23).
• Cut as described in section 9.3.
9.7 Mitre cut 0°- 45° and turntable 0°- 45°
(fig. 1/2/3/6)
The cross cut mitre saw can be used to make mitre cuts to the
left of 0°- 45° in relation to the work face and, at the same
time, 0° - 45° to the left or 0° - 45° to the right in relation to
the stop rail (double mitre cut).
10 GB/CY
Attention! For mitre cuts (inclined saw head), the
moveable stop rail (8a) must be fixed in the outer
position.
• Open the set screw (8b) for the moveable stop rail (8a) and
push the moveable stop rail (8a) outwards.
• The adjustable stop rail (8a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (8a) and the saw blade (6) amounts to a maximum
of 8 mm.
• Before making a cut, check that the stop rail (8a) and the
saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Move the machine head (4) to its upper position.
• Release the rotary table (13) by loosening the set screw (7).
• Using the handle (3), set the rotary table (13) to the desired
angle.
• Retighten the set screw (7) in order to secure the rotary table.
• Undo the locking screw (23).
• Use the handle (3) to tilt the machine head (4) to the left until
it coincides with the required angle value (in this connection
see also section 9.6).
• Re-tighten the locking screw (23).
• Cut as described under section 9.3.
9.8 Limiting the cutting depth (fig. 3)
• The cutting depth can be infinitely adjusted using the screw
(24). To do this loosen the locknut (24a) on the screw (24).
Turn the screw (24) in or out to set the required cutting depth.
Then re-tighten the locknut (24a) on the screw (24).
• Check the setting by completing a test cut.
9.9 Changing the saw blade (fig. 1/2/3/9/10)
Remove the power plug!
Important!
Wear safety gloves when changing the saw blade.

Risk of injury!

• Swing the machine head (4) upwards and secure with the
stop for cutting depth limiting (25).
• Fold the saw blade guard (5) upwards until the saw blade
guard (5) is above the flange screw (29).
• With one hand insert the Allen key (C) in the flange screw
(29).
• Hold the Allen key (C) and slowly close the saw blade guard
(5) until it touches the Allen key (C).
• Firmly press the saw shaft lock (32) and slowly rotate the
flange screw (29) in clockwise direction. The saw shaft lock
(32) engages after no more than one rotation.
• Now, using a little more force, slacken the flange screw (29)
in the clockwise direction.
• Turn the flange screw (29) right out and remove the outer
flange (30).
• Take the blade (6) off the inner flange and pull out down-
wards.
• Carefully clean the flange screw (29), outer flange (30) and
inner flange.
• Fit and fasten the new saw blade (6) in reverse order.
• Important! The cutting angle of the teeth, in other words the
direction of rotation of the saw blade (6) must coincide with
the direction of the arrow on the housing.
• Before continuing your work make sure that all safety de-
vices are in good working condition.