Technical Data; Protecting The Environment; Declaration Of Conformity - Stanley FATMAX SFMCE510 Bedienungsanleitung

ENGLISH
When cutting metal spread a thin film of oil along the cut-
u
ting line before cutting.
When sanding new layers of paint before applying another
u
layer, use extra fine grit.
On very uneven surfaces, or when removing layers of
u
paint, start with a coarse grit. On other surfaces, start with
a medium grit. In both cases, gradually change to a fine
grit for a smooth finish.
Consult your retailer for more information on available
u
accessories.
Maintenance
Your Stanley Fat Max corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.

Protecting the environment

Z
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com.
12
(Original instructions)

Technical data

Voltage V
DC
No-load speed
min
-1
Oscillating angle Degrees
Weight kg
Charger SFMCB11
Input Voltage V
AC
Output Voltage V
DC
Current A
Battery SFMCB201
Voltage
V 18
DC
Capacity Ah 1.5
Type
Li-Ion
Level of sound pressure according to EN62841:
Sound pressure (L ) 88 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L ) 99 dB(A), uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN62841:
Vibration emission value a = 14 m/s
2
h

Declaration of Conformity

The Supply of Machinery (Safety) Regulations 2008
Cordless Oscillating Tool - SFMCE510
Stanley Europe declares that these products described under
"technical data" are in compliance with:
EN62841-1:2015, EN62841-2-4:2014.
These products conform to the following UK Regulations:
The Supply of Machinery (Safety) Regulations, 2008, S.I.
2008/1597 (as amended).
Electromagnetic Compatibility Regulations, 2016,
S.I.2016/1091 (as amended).
The Restriction of the Use of Certain Hazardous Substances
in Electrical and Electronic Equipment Regulations 2012, S.I.
2012/3032 (as amended).
For more information, please contact Stanley Europe at the
following address or refer to the back of the manual.
SFMCE510 H1
0 - 19000
1.6 or 3.2
0.89 (bare unit, no battery)
SFMCB12 SFMCB14
230 230
18 18
1.25 2
SFMCB202 SFMCB204 SFMCB206
18 18
2.0 4.0
Li-Ion Li-Ion
K = 1,5 m/s2
18
230
18
4
18
6.0
Li-Ion