Accessories - Black & Decker BEPW1300H Bersetzt Von Den Originalanweisungen

ENGLISH
11. Actuate the trigger of the spray handle to start
cleaning work.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
@
care and regular cleaning.
WARNING! Before performing any maintenance on
the tool.
Š Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Š Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent‑based cleaner.
@
Cleaning
WARNING: Blow dirt and dust out of all air vents
with clean, dry air at least once a week. To minimize
the risk of eye injury, always wear approved eye
@
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Nozzle Cleaning (Fig. A, G)
If the nozzle becomes clogged with foreign materials, such as
dirt, excessive pressure may develop. If the nozzle becomes
partially clogged or restricted, the pump pressure will pulsate.
Clean the nozzle immediately using the nozzle cleaner.
1. Turn OFF and unplug the pressure washer unit ( 8 ).
2. Turn OFF the water supply.
3. Pull trigger ( 7 ) on spray handle ( 4 ) to relieve any
water pressure.
4. Remove the nozzle from the spray wand ( 2 ) by
depressing the button ( 3 ).
5. Using the nozzle cleaning tool ( 14 ), unclog any debris
from the nozzle.
6. Run water from a faucet or garden hose through
the nozzle.
Filter Cleaning (Fig. A, L)
Inspect the filter ( 21 ) before each use and clean if necessary.
Remove the filter element and run under clear water to
remove any debris.
12
(Original instructions)
Storage (Fig. H, I)
• Store in a dry, covered location above freezing
temperature. STORE INDOORS.
• Always completely empty water from high pressure hose,
pressure washer unit, nozzles, and spray wand.
• Nozzles can be stored in the nozzle storage ( 29 ) section
of the bracket ( 26 ) as shown in Fig. H.
• Power cord can be stored coiled up around the pressure
washer unit and secured with the cord retaining
hooks ( 17 ) as shown in Fig. H.
• High pressure hose ( 1 ) can be stored coiled up and
secured to the handle using the supplied hook and latch
strap ( 27 ) as shown in Fig. I.
• The spray handle ( 4 ) can be stored onto the rear of the
unit using the bracket ( 26 ) as shown in Fig. I.
• The spray wand ( 2 ) can be stored into the handle as
shown in Fig. I.
@

Accessories

WARNING: Since accessories, other than those
offered by Black+Decker, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce risk of injury, use
only Black+Decker accessories recommended for
this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
@
Repairs
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a Black+Decker factory service
center or a Black+Decker authorized service center.
Always use identical replacement parts
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Š Safely dispose of the old plug.
Š Connect the brown lead to the live terminal in the
new plug.
@
Š Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth
terminal. Follow the fitting instructions supplied with
good quality plugs.
Recommended fuse: 13 A.