Safe Working - ATIKA RLC 40-10G Originalbetriebsanleitung

sufficient break times may result in a hand-arm vibration syn-
drome.
The extent of exposure depending on the type of work or ma-
chine use should be estimated and appropriate breaks taken. In
this way, the extent of exposure can be considerably reduced
over the entire work time. Minimise the risk caused by vibra-
tions. Maintain this machine according to the instructions in the
manual.
Avoid the use of this machine at temperatures under 10°C.
Create a work schedule in order to minimise vibration exposure.
S a f
S a f
Pass the safety instructions on to all persons who work

with the machine.
Children and young persons under 16 years of age as

well as persons who have not read the instruction man-
ual are not allowed to operate this product.

Keep these safety instructions in a safe place.

Follow the attached "General safety instructions".
 Do not use the machine for unsuitable purposes (see "Nor-
mal intended use" and "Working with the agitator").
Do not touch, inhal (dust) or swallow cement and

additives. Wear personal protective equipment (gloves,
safety goggles, face mask) when filling or emptying the mix-
ing container.
 Keep children, bystanders and animals at a distance from
your working area. Do not allow other persons, especially
children, to touch the tool or the cable.
 Switch off the machine if persons, in particular children or
pets, are close to you or if you change your working area.
 The operator is resposnible to third persons within the area
of operations.
 The operator is responsible for accidents or risks which
occur to other persons or their properties.
 Never operate the machine if other persons are in the im-
mediate vicinity.
 Never leave the device unattended.
 Only operate the machine with complete and correctly at-
tached safety equipment and do not alter anything on the
machine that could impair the safety.
 Do not modify the device or parts of the device respectively.
Switch the machine off and remove the re-

move the battery before
carrying out repair works

maintenance and cleaning

eliminating faults.

checking connecting lines, whether these are knotted or

damaged.
transport

leaving unattended (even during short interruptions).

unusual noises and vibrations

 Thoroughly maintain your agitator:
Make sure that the ventilation apertures are free.

Keep handles dry and free of oils and grease. Follow the

maintenance instructions.
e w o r k i n g
e w o r k i n g
 Check the machine for possible damage:
Before further use of the machine the safety devices

must be checked carefully for their proper and intended
function.
Check whether movable parts function perfectly and do

not stick or whether parts are damaged. All parts must
be correctly installed and fulfil all conditions to ensure
perfect operation of the machine.
Damaged guards and parts must be properly repaired or

exchanged by a recognized, specialist workshop; insofar
as nothing else is stated in the instructions for use.
Damaged or illegible safety labels should be replaced

immediately.
 Store unused equipment in a dry, locked place out of the
reach of children.
Safety instructions for agitators
a) Hold the power tool with both hands by the handles
provided. Loss of control may result in injury.
b) To avoid a dangerous atmosphere, ensure adequate
ventilation when mixing flammable substances. Vapours
formed may be inhaled or ignited by sparks generated by
power tools.
c) Do not stir any food. Power tools and their implements are
not designed for processing food.
d) Keep the power cords away from the work area. The
power cord can get caught in the beater.
e) Ensure that the agitator tank is firmly and safely posi-
tioned. An improperly secured container may move unex-
pectedly.
f) Make sure that no liquid splashes against the housing of
the power tool. Liquid entering the power tool may cause
damage and electric shock.
g) Follow the directions and safety instructions for the
material to be mixed. The material to be mixed can be
harmful to health.
h) If the power tool falls into the material to be mixed, im-
mediately unplug the power plug and have the power
tool checked by qualified personnel. Reaching into the
container with the power tool still hanging from the socket in-
side it can lead to an electric shock.
i) During the stirring process, do not reach into the agita-
tor container with your hands or insert any other ob-
jects. Contact with the beater can lead to serious injuries.
j) Only let the power tool start up and come to a stop in the
agitator tank. The beater can spin around or bend in an un-
controlled manner.

Refer to the enclosed brochure "General safety instruc-
tions" for additional safety notices.
13