Verwandte Anleitungen für Datalogic DLC6000 serie
Inhaltszusammenfassung für Datalogic DLC6000 serie
- Seite 1 DLC6000 SERIES CCD READERS QUICK REFERENCE INSTALLAZIONE RAPIDA INSTALLATION RAPIDE SCHNELLINSTALLATION 820000512 (Rev. B)
- Seite 2 USING DLC6000 CCD READERS scanning line code surface DLC6000 CCD READERS automatically scan barcodes on contact. Some models have a trigger which must be pressed to read a code. Code scanning is performed along an imaginary line passing across the reading window. This imaginary line must pass through the entire code.
-
Seite 3: Technical Features
Reading field width 63 mm typical 80 mm typical Max. resolution 0.1 mm, 4 mils 0.13 mm, 5 mils min. 15% (Datalogic Test Chart) Reading indicators LED, Beeper Environmental Features 0 °C to + 55 °C Working Temperature -20 °C to + 70 °C... - Seite 4 CONNECTIONS RS232 With the RS232 cable, this accessory device is intended to be supplied by a UL Listed Direct Plug-in Power Unit marked "Class 2", rated 5 V, minimum 150 mA. WEDGE With the Wedge or PC Notebook cables, this accessory device is intended to be connected to a UL Listed Computer which supplies power directly to the reader.
-
Seite 5: Disconnecting The Cable
PEN EMULATION Pen cable Portable Multidrop network terminal A F1 C F2 E F3 or other func G CL I PG Host system cl r Pen cable With the Pen Emulation cable, this accessory device is intended to be supplied by a UL Listed Power Unit marked "Class 2", or an LPS power source which supplies power directly to the reader. -
Seite 6: Restore Default
1 DEFAULT Read the RESTORE DEFAULT. Leggere il codice che ripristina i default. Lecture du code de configuration par défaut. Lesen Sie den Restore Default Code, um die Werkseinstellung wieder herzustellen. RESTORE DEFAULT RS232 DEFAULT SETTINGS 9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking, ack/nack disabled, fifo enabled, delay disabled, rx timeout 5 sec., serial trigger lock disabled;... - Seite 7 DECODING PARAMETERS ink spread enabled, overflow control enabled, interdigit control enabled, decoding safety = one read CODE SELECTION enabled codes • EAN 8 / EAN 13 / UPC A / UPC E without ADD ON check digit transmitted, no conversions •...
- Seite 8 2 READER CONFIGURATION Read the interface selection code for your applica- tion. Leggere il codice per la selezione dell’interfaccia relativo al modo di comunicazione desiderato. Lecture du code “Interface” correspondant à votre modèle. Lesen Sie denjenigen Schnittstellen-Code, der Ihrem gewünschten Kommunikationsmodus entspricht.
- Seite 9 WEDGE (continued) IBM Terminal 3153 IBM Terminals 31xx, 32xx, 34xx, 37xx: To select the interface for these IBM Terminals, read the correct KEY TRANSMISSION code. Select the KEYBOARD TYPE if necessary (default = advanced keyboard). Per selezionare l'interfaccia per i terminali IBM, leg- gere il codice Key Transmission appropriato e, se necessario, il codice Keyboard Type (default = advanced keyboard).
-
Seite 10: Wedge Keyboard Nationality
WEDGE KEYBOARD NATIONALITY Wedge users should select one of the following WEDGE KEYBOARD NATIONALITY codes. Quando è selezionata l’interfaccia Wedge, leggere uno dei seguenti codici per impostare la nazionalità della tastiera. Pour l’interface Wedge, lire l'un des codes suivants pour sélectionner la nationalité du clavier. Für den Betrieb mit einer Wedge-Schnittstelle lesen Sie einen der folgenden Codes, um die Tastaturnatio- nalität einzustellen. - Seite 11 YOUR READER IS NOW READY TO READ BARCODES. To change the defaults, see the Hand-Held Devices Software Configuration Manual, part number 90ACC1854. IL LETTORE È PRONTO A LEGGERE I CODICI. Per cambiare i parametri di default, fare riferimento manuale "Hand-Held Devices Software Configuration Manual", n.
-
Seite 12: Operating Test
3 OPERATING TEST Read the TEST codes below. Leggere i codici di test. Lire les codes tests. Lesen Sie die Test-Coden. EAN-8 1 2 3 4 5 6 7 0 EAN-13 1 2 3 4 5 6 7 0 0 0 9 9 2 Code 39 (Normal) Code 128 Interleaved 2 of 5... - Seite 13 STANDBY ONLY readers with button/trigger Setting the Standby parameter allows you to optimize the reader for low power consumption or reading speed. SOLO per lettori con pulsante Il parametro Standby consente di ottimizzare il risparmio energetico o la velocità di lettura. SEULEMENT pour douchettes avec bouton Le paramètre "Standby"...
- Seite 14 Datalogic garantit ce produit de tout défaut de fabrication ou des matériels pendant 24 mois de la date de livraison, à condition que le produit soit utlisé correctement. Datalogic a la faculté de réparer ou de remplacer ce produit. mesures prolongeront l’échéance de la garantie.
-
Seite 15: Fcc Compliance
PATENTS This product is licensed under one or more of the following U.S. patents: 4,282,425; 4,570,057; 4,766,300; 4,894,523; 5,021,642; 5,038,024; 5,081,343; 5,095,197; 5,144,119; 5,144,121; 5,182,441; 5,187,355; 5,187,356; 5,218,191; 5,233,172; 5,258,606 and /or 5,288,985 This product is covered by one or more of the following patents and patent applications: US 5,917,176;... - Seite 16 DATALOGIC S.p.A., Via Candini, 2 40012 - Lippo di Calderara Bologna - Italy dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el DLC60XX-X Touch Reader e tutti i suoi modelli and all its models et tous ses modèles...