Technical Data; Noise/Vibration Information - Bosch EasyHedgeCut 45 Bedienungsanleitung

12 | English
(1) Handle (insulated gripping surface)
(2) On/Off switch
(3) Lock-off button for On/Off switch
(4) Hand guard

Technical Data

Hedgecutter
Article number
Rated power input
No-load stroke speed
Cutting length
Tooth opening
Weight according to
EPTA‑Procedure 01:2014
Protection class
Serial number
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Noise/Vibration Information

That the declared vibration total value(s) and the declared
noise emission value(s) have been measured in accordance
with a standard test method any may be used for comparing
one tool to another.
That the declared vibration total value(s) and the declared
noise emission value(s) may also be used in a preliminary as-
sessment of exposure.
That the vibration and noise emissions during actual use of
the power tool can differ from the declared values depend-
ing on the ways in which the tool is used especially what kind
of workpiece is processed; and of the need to identify safety
measures to protect the operator that are based on an estim-
ation of the exposure measures in the actual conditions of
use (taking account of all parts of the operating cycle such as
the times when the tool is switched off and when it is running
idle in addition to the trigger time).
Noise emission values determined according to EN
62841-4-2:2019 .
Typically the A-weighted noise levels of the product are:
Sound pressure level 75 dB(A); sound power level
95 dB(A). Uncertainty K = 2.0 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-4-2:2019:
2 2
a = 2.5 m/s , K = 1.5 m/s .
h
Troubleshooting
F 016 L94 104 | (28.09.2020)
(5) Blade
(6) Protection sleeve
(7) Mains plug
(8) Extension cable
A) country specific
EasyHedgeCut 45 EasyHedgeCut 46 EasyHedgeCut 50 EasyHedgeCut 55
3 600 H47 A.. 3 600 H47 A06
W 420
-1
min 3400
mm 450
mm 16
kg 2.6
/ II
Operation
u
Switching ON/OFF (see figures C and D)
To switch ON, firstly press and hold the lock-off button for
On/Off switch (3). Then press the On/Off switch (2) and
keep it pressed.
To switch OFF, release the lock-off button for On/Off switch
(3) and then release the On/Off switch (2).
Working with the Hedgecutter (see figure E)
Move the hedgecutter evenly forward along the cutting line.
The double edge cutting blade enables cutting in either dir-
ection, or with a side to side motion.
Cut the sides of the hedge first, then the top.
To cut the sides straightly, we recommend cutting from bot-
tom to top in the direction of growth. Younger stems tend to
move outwards when cutting them from top to bottom, res-
ulting in shallow patches or holes in the hedge.
To reach a level finish, fasten a piece of string along the
length of the hedge at the required height and use as an
alignment guide. Cut the hedge just above the string.
Pay attention that no objects such as wires are cut. The
blade or drive can be damaged.
A)
3 600 H47 B..
420 450
3400 3400
450 500
16
2.6
/ II
see type plate on garden tool
Pay attention to the mains voltage. The voltage of the
power source must match the voltage specified on the
rating plate of the machine.
3 600 H47 C..
450
1700/3400
550
16 16
2.7 2.8
/ II / II
Bosch Power Tools