Product Description And Specifications; Product Features - Bosch GBM 13 HRE Professional Originalbetriebsanleitung

Safety Warnings for Drills
Safety instructions for all operations
Use the auxiliary handle(s). Loss of control can cause
u
personal injury.
Hold the power tool by insulated gripping surfaces,
u
when performing an operation where the cutting ac-
cessory or fasteners may contact hidden wiring or its
own cord. Cutting accessory or fasteners contacting a
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Safety instructions when using long drill bits
Never operate at higher speed than the maximum
u
speed rating of the drill bit. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Always start drilling at low speed and with the bit tip
u
in contact with the workpiece. At higher speeds, the bit
is likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do
u
not apply excessive pressure.Bits can bend causing
breakage or loss of control, resulting in personal injury.
Additional safety warnings
Switch the power tool off immediately if the applica-
u
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
Hold the power tool securely. When tightening and
u
loosening screws be prepared for temporarily high torque
reactions.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Bosch Power Tools
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is suitable for drilling in wood, metal, ceramic
and plastic. Power tools with electronic control and clock-
wise/anti-clockwise rotation are also suitable for screwdriv-
ing and thread cutting.

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Keyed chuck
(2) Rotational direction switch
(3) On/off switch
(4) Lock-on button for on/off switch
(5) Auxiliary handle (insulated gripping surface)
(6) Chuck key
(7) Handle (insulated gripping surface)
A)
(8) Screwdriver bit
A)
(9) Universal bit holder
(10) Securing screw for keyed chuck
A)
(11) Hex key
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Drill
Article number
Rated power input
Power output
No-load speed
Max. speed under load
Rated torque
Spindle collar diameter
Max. drilling diameter
– Steel
– Wood
– Aluminium
Chuck capacity
Weight according to
EPTA-Procedure 01:2014
English | 11
GBM 13 HRE
3 601 K49 6..
W 550
W 285
-1
min 0–550
-1
min 450
Nm 5
mm 43
mm 13
mm 40
mm 20
mm 1.5–13
kg 2.1
1 609 92A 5AG | (12.11.2019)