Endress+Hauser Cerabar S PMC71 Betriebsanleitung Seite 38

Bedienung
Parameternamen gemäß DD
MEASURED_LEVEL_EASY
FULL_CALIBRATION_EASY
EMPTY_CALIBRATION_EASY
FULL_PRESSURE_EASY
EMPTY_PRESSURE_EASY
Parameternamen gemäß DD
DEVICE_DIALOG
SW_LOCK
STATUS_LOCKING
CONFIGURATION_COUNTER
ELECTRONICS_TEMPERATURE
ELECTRONICS_TEMP_LOW_LIMIT
ELECTRONICS_TEMP_HIGH_LIMIT
PMAX_PROC_CONN
SENSOR_MEAS_TYPE
SENSOR_MIN_ABSOLUTE_LIMIT
SENSOR_MAX_ABSOLUTE_LIMIT
SENSOR_TEMP_LOW_LIMIT
SENSOR_TEMP_HIGH_LIMIT
SENSOR_HARDWARE_REV
COUNTER P_MAX
MAX_MEASURED_PRESSURE
COUNTER_PMIN
MIN_MEASURED_PRESSURE
COUNTER_TMAX
MAX_MEASURED_TEMP
COUNTER_TMIN
MIN_MEASURED_TEMP
ELECTRONIC_OVER_TEMP_COUNTER
ELECTRONIC_OVER_TEMPERATURE
ELECTRONIC_UNDER_TEMP_COUNTER
ELECTRONIC_UNDER_TEMPERATURE
RESET_PEAK_HOLD
PRESSURE
CORRECTED_PRESSURE
MEASURED_VALUE_TREND
MAX_TURNDOWN
SENSOR_CHANGES
PRESSURE_PEAK_HOLD_STEP
TEMP_PEAK_HOLD_STEP
ACCELERATION_OF_GRAVITY
CREEP_FLOW_HYST
HISTOROM_SAVING_CYCLE_TIME
HISTOROM_AVAIBLE
DOWNLOAD_SELECTION
HISTOROM_CONTROL
PRESSURE_UNIT
TEMPERATURE_UNIT
INPUT_PRESSURE_INVERSION
Parameternamen gemäß DD
DEVICE DIALOG
DISPLAY_MAINLINE_CONTENT
DISPLAY_MAINLINE_FORMAT
38
Parameternamen, Option Index Data type
"Label Parameter" und
Darstellung FieldCare
GEMESSENER FÜLLSTAND 92
LEVEL EASY
ABGLEICH VOLL 93
ABGLEICH LEER 94
DRUCK VOLL 95
DRUCK LEER 96
Service Transducer Block
Parameternamen, Option
"Label Parameter" und
Darstellung FieldCare
GERÄTE DIALOG
FREIGABECODE
STATUS LOCKING
KONFIG ZÄHLER
TEMP. ELEKTRONIK
Tmin ELEKTRONIK
Pmax ELEKTRONIK
Pmax Anschluss
SENSORMESSTYP
Pmin SENSOR. Abs
Pmax SENSOR. Abs
Tmin SENSOR
Tmax SENSOR
SENSOR HW REVISION
ZÄHLER P > Pmax
MAXIMALER DRUCK
ZÄHLER P < Pmin
MINIMALER DRUCK
ZÄHLER T > Tmax
MAXIMALE TEMP.
ZÄHLER T < Tmin
MINIMALE TEMP.
ZÄHL. EL. T > Tmax
MAX. EL. TEMP
ZÄHL. EL. T< Tmin
MIN. EL. TEMP.
RESET SCHLEPPZEI
DRUCK GEMESSEN
DRUCK N. LAGEKOR
TENDENZ MESSWERT
MAX TURNDOWN1
SENSORWECHSEL
P. SCHLPZ. SCHRITT
T. SCHLPZ. SCHRITT
GRAVITATION
SCHLEICHM. HYST.
HIST. SPEICH. ZYKL.
HISTOROM VORHND.
DOWNLOAD FUNCT.
HISTOROM FUNKT.
EINHEIT DRUCK
TEMP. EINHEIT
DRUCK INVERT.
Display Transducer Block
Parameternamen, Option Index Data type
"Label Parameter" und
Darstellung FieldCare
GERÄTE DIALOG 10
INHALT HAUPTZEIL 11
FORMAT HAUPTZEIL 12
Cerabar S PMC71, PMP71, PMP75 mit FOUNDATION Fieldbus
Größe Storage
(Byte) Class
Float 4 D
Float 4 S
Float 4 S
Float 4 S
Float 4 S
Index Data type Größe Storage
(Byte) Class
11 Unsigned8 1 D
12 Unsigned16 2 S
13 Unsigned8 1 D
14 Unsigned16 2 S
15 Float 4 D
16 Float 4 S
17 Float 4 S
18 Float 4 S
19 Unsigned16 2 S
20 Float 4 S
21 Float 4 S
22 Float 4 S
23 Float 4 S
24 Unsigned8 1 S
25 DS-65 5 S
26 DS-65 5 S
27 Unsigned16 2 S
28 Float 4 S
29 Unsigned16 2 S
30 Float 4 S
31 Unsigned16 2 S
32 Float 4 S
33 Unsigned16 2 S
34 Float 4 S
35 Unsigned16 2 S
36 Float 4 S
37 Unsigned8 1 D
38 DS-65 5 D
39 Float 4 D
40 Unsigned8 1 D
41 Float 4 S
42 Unsigned16 2 S
43 Float 4 S
44 Float 4 S
45 Float 4 S
46 Float 4 S
47 Unsigned8 1 S
48 Unsigned8 1 S
49 Unsigned8 1 D
50 Unsigned8 1 D
51 Unsigned16 2 S
52 Unsigned16 2 S
53 Unsigned8 1 S
Größe Storage
(Byte) Class
Unsigned8 1 D
Unsigned8 1 S
Unsigned8 1 S
Read Write MODE_BLK Resetcodes
x
x x OOS
x x OOS
x x OOS
x x OOS
Read Write MODE_BLK Resetcodes
x
x x
x
x
x
x
x
x x AUTO, OOS
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x x AUTO, OOS
x
x
x
x x
x x
x x
x x
x x OOS
x x OOS
x x
x
x x
x x
x
x
x x
Read Write BLK_MODE
x
x x AUTO, OOS
x x AUTO, OOS
Endress+Hauser
7864, 333
7864, 333
7864, 333
7864, 333
7864, 333
Resetcodes
1864
1864