The Remote Control; Before Operating; Setting Up The Device - Block CR-20 Bedienungsanleitung

Remote control
1.
2.
1 3
5 6
17
4
3.
13 14
7 8
4.
15
20
9
5.
13
10 12
6.
11
7.
16
2
8.
18
9.
10.
19
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
40
„Standby" button: switches the device to „Clock" mode, the display
will show the time and the date. To save energy, switch off the device
in the net counter.
„Mode" button : By pressing, the display switches to the overview
mode. You can now use the multifunction knob or the arrow keys on
the Remote control select the music source
„Snooze / Sleep" Button sets sleep timer of the device in the
following time units: 15, 30, 45 and 60 min
Taste „Mode": One or more short presses will display additional
information about the music source (if any) on the display. Long press
calls up the menu of the device.
„Menu/Info": One or more short presses will display additional
information about the music source (if any) on the display. Long press
calls up the menu of the device.
„Alarm" button
Alarm button: : Pressing this button sets the alarm
function of the CR-20.
„Back" button: on radio mode, the device searches the previous lo
wer transmitter. On CD and media player mode, the unit jumps to the
previous track.
„Forward" button: on radio mode, the device searches the next higher
transmitter. On CD and Media Player mode, the device jumps to the
next track.
Arrow upwards: on FM mode to increase the frequency in 0.05 MHz . In
menu to select the different points.
Arrow to the left: to reach the previous setting in the menu.
Arrow down: in FM mode by the frequency in 0.05 MHz increments to
reduce. To select the different points in the menu.
Arrow to the right: to access selected functions in the menu.
"Play" button
„Stop" button.
„Volume +" button: increases the volume
„Volume -" button: reduces the volume
„REPEAT/RANDOM": Press once to start the repeat function for
the current title, press the repeat function twice whole media (for
example, CD, USB, media server) a third press ends all Repeat. Long
press starts the playback of the entire medium in random Sequence,
pressing again for a long time ends this function. Watch out for the
displays at the bottom of the display.
Button „1 - 10": on radio mode, recalls on the stored transmitters
and on CD mode, it chooses the single pieces of the CD.
T„P" button: recalls or saves pre-set transmitters in radio mode.
„EQ" button: A short press calls up the equalizer menu.

Before operating

Before you can use your Internet radio, the streaming functionality or the operation via smart phone app, you need:
1. A fast internet connection.
2. A router, preferably with WLAN (wireless access point).
3. If your wireless network is protected with Wired Equivalent Privacy (WEP) or with Wi-Fi Protected Access
(WPA), you will need a WEP or a WPA code, so that your Internet radio can be connected to the router.
4. Before proceeding, make sure that your wireless network is turned on and has a broadband internet
access.
5. In case of problems while connecting your device to the router, please try to solve them using the manual
instructions of the router.

Setting up the device

1. Connect the FM and DAB + telescopic antenna to the device. Then pull the telescopic aerial to full length.
Later, when setting up your channels, you can optimize the reception quality just changing the angle of
inclination and the tilt angle of the aerials.
2. If you want wirelessly to connect your CR-20 to the Internet via an existing wireless Network, please
mount the included WLAN antenna
3. Connect the connection cable of the enclosed power supply unit to the device and plug this into a power
outlet
41