Skil 1081 Betriebsanleitung Seite 6

binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR SANDERS
GENERAL
• This tool should not be used by people under the age
of 16 years
• This tool is not suitable for wet sanding
• Never use the tool when cord is damaged; have it
replaced by a qualified person
• Do not work materials containing asbestos
(asbestos is considered carcinogenic)
• Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
• SKIL can assure flawless functioning of the tool only
when original accessories are used
• Do not continue to use worn, torn or heavily clogged
sanding discs
BEFORE USE
• Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to
a 220V supply)
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• The noise level when working can exceed 85 dB(A);
wear ear protection
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classified as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
• Follow the dust-related national requirements for the
materials you want to work with
• Wear protective gloves, safety glasses, close-fitting
clothes and hair protection (for long hair)
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• When sanding metal, sparks are generated; do not
use dustbox and keep other persons and combustible
material from work area
DURING USE
• Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool
• Do not touch the moving sanding disc
• In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
AFTER USE
• When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of
this tool, it must be disposed of safely and not left
unattended
USE
• Backing pads
- never run the tool without backing pad A
! replace damaged backing pads immediately
(loosen/fasten 4 pad screws B)
! unplug tool before removing/mounting backing
pads
• Mounting of sanding sheet ④
- mount VELCRO sanding sheet C as illustrated
- if necessary, clean backing pad first
! perforation in sanding sheet should correspond
with perforation in sanding foot
! the dust suction requires the use of perforated
sanding sheets
! replace worn sanding sheets in time
• Dust suction ⑤
For optimal dust pick-up performance
- mount dustbag D
- empty dustbag regularly
! do not use dustbag when sanding metal
• On/off
- before switching on the tool, you should place it with
the entire sanding surface on the workpiece
- when switching on, do not apply too much pressure
on the tool
- switch on/off the tool by pulling/releasing trigger E ②
! be aware of the sudden impact when the tool is
switched on
! before switching off the tool, you should lift it
from the workpiece
• Switch lock ⑥
- pull trigger E
- press knob F with your thumb
- release the trigger
- unlock the switch by pulling again trigger E and then
releasing it
6