Herunterladen Inhalt Inhalt Diese Seite drucken

Bosch PSB 500 RE Bedienungsanleitung Seite 13

Vorschau ausblenden Andere Handbücher für PSB 500 RE:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
Technical Data
Impact Drill
Article number
Rated power input
Output power
No-load speed
Rated speed
Impact rate
Rated torque
Torque at max. output power
Right/left rotation
Spindle collar dia.
Max. drilling dia.
– Concrete
– Steel
– Wood
Chuck clamping range
Weight according to EPTA-Procedure 01/2003
Protection class
The values given are valid for nominal voltages [U] of 230/240 V. For lower voltage and models for specific countries, these val-
ues can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
Declaration of Conformity
We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or
standardization documents: EN 60745 according to
the
provisions
of
98/37/EC.
Dr. Egbert Schneider
Senior Vice President
Engineering
25.04.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Noise/Vibration Information
Measured values determined according to EN 60745.
Typically the A-weighted noise levels of the product
are: Sound pressure level 97 dB(A); Sound power
level 108 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values (triax vector sum) determined
according to EN 60745:
Drilling
into
metal:
2
a
=4.7 m/s
, Uncertainty K =1.5 m/s
h
Impact drilling into concrete: Vibration emission value
2
a
=24.2 m/s
, Uncertainty K =2.0 m/s
h
Screwdriving: Vibration emission value a
Uncertainty K =1.5 m/s
2 609 002 311 • 8.5.07
the
directives
89/336/EEC,
Dr. Eckerhard Strötgen
Head of Product
Certification
Vibration
emission
2
,
2
,
< 2.5 m/s
h
2
.
W
W
rpm
rpm
bpm
Nm
Nm
mm
mm
mm
mm
mm
kg
WARNING
ured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another.
The vibration emission level will vary because of the
ways in which a power tool can be used and may
increase above the level given in this information sheet.
This could lead to a significant underestimate of expo-
sure when the tool is used regularly in such a way.
Note: To be accurate, an estimation of the level of
exposure to vibration experienced during a given period
of work should also take into account the times when
the tool is switched off and when it is running but not
actually doing the job. This may significantly reduce the
exposure level over the total working period.
Assembly
Before any work on the machine itself, pull
the mains plug.
Auxiliary Handle (see figure A)
Operate your machine only with the auxiliary
handle 10.
The auxiliary handle 10 can be set to any position for a
value
secure and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary
handle 9 in anticlockwise direction and set the auxiliary
2
handle 10 to the required position. Then tighten the
,
wing bolt 9 again in clockwise direction.
PSB 500 RE
3 603 A26 0..
500
228
50 – 3000
2380
48000
0.9
7.5
43
13
10
20
2.0 – 13
1.5
/II
The vibration emission level given in
this information sheet has been meas-
PSB 550 RE
3 603 A26 0..
550
270
50 – 3000
2246
48000
1.2
7.5
43
13
10
20
2.0 – 13
1.5
/II
English | 13

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Psb 550 re

Inhaltsverzeichnis