Using Your Appliance; After Use; Safety Of Others - Black & Decker BCSC115 Originalanweisungen

ENGLISH
Save all warnings and instructions for future reference.
u

Using your appliance

Always take care when using the appliance.
u
Keep work area clean and well lit. Cluttered or dark areas
u
invite accidents.
Do not expose the appliance to rain or wet conditions.
u
Water entering the appliance will increase the risk of
electric shock.
Do not immerse the appliance in water.
u
Only use the appliance in daylight or good artificial light.
u
Do not operate your appliance in explosive atmospheres,
u
such as in the presence of flammable liquids, gases
or dust.
The appliance is not to be used as a toy.
u
Do not open body casing. There are no user serviceable
u
parts inside.
Disconnect the battery from the appliance when not in
u
use, before fitting or removing parts and before cleaning.
Appliance use and care
Before use, check the appliance for damaged or defective
u
parts.
Check for breakage of parts, damage to switches and any
other conditions that may affect its operation.
Do not use the appliance if the switch
u
turn it on and off. Any appliance that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or the
u
battery pack from the appliance before making any adjust-
ments, changing accessories, or storing appliances. Such
preventive safety measures reduce the risk of starting the
appliance accidentally.
Do not use the appliance if any part is damaged or defec-
u
tive.
Have any damaged or defective parts repaired or replaced
u
by an authorised repair agent.
Never attempt to remove or replace any parts other than
u
those specified in this manual.
Additional safety instructions for Scissors.
Hold tool by insulated gripping surfaces when per-
u
forming an
operation where the cutting tool may contact hidden
wiring. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock
Cut material at or below rated capacity.
u
NEVER have any part of your body near the blades.
u
Serious personal injury may result.
Keep hands away from cutting area. A moment of inat-
u
tention while operating power tools may result in serious
personal injury.
6
(Original instructions)
does not
.
ALWAYS wear gloves when handling sheet metal. The
u
edges are sharp and can cause serious personal injury.
Firmly secure the piece of metal to be cut to prevent
u
movement during cutting.
ALWAYS start tool before engaging material to be cut.
u
If possible, cut material so scrap curl is to the right.
u
This direction will move curl down and out of the way.
Use shears upright. If tool is upside down, metal curl
u
.
may turn toward you
DO NOT use the shear with any kind of accessory or
u
attachment.
Always wear safety shoes to protect your feet from
u
sharp metal debris on the floor.
Keep all screws tight. Check periodically for loosening.
u
Do not place anything into the motor housing open-
u
ings.

After Use

Switch off before leaving the appliance unattended and
u
before changing, cleaning or inspecting any parts of the
appliance.
When not in use, the appliance should be stored in a dry,
u
well ventilated place out of the reach of children.
Children should not have access to stored appliances.
u
Service
Have your appliance serviced by a qualified repair person
u
using only identical replacement parts. This will
ensure that the safety of the appliance is maintained.

Safety of others

This appliance can be used by children aged from 8 years
u
and above and persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concern-
ing use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Children should be supervised to ensure that they do not
u
play with the appliance.
Labels on Appliance
The following symbols, along with the date code, are shown
on the appliance:
Warning! To reduce the risk of injury, the user
must read the instruction manual.