Unpacking Your Tool; Before Use - Silverline 980960 Bedienungsanleitung

EN
Product Familiarisation
1. Direction Indicator
2. Spindle Lock Button
3. Handle Location Points
4. ON/OFF Slider Switch
5. Rear Handle
6. Battery Mount
7. Battery Release
8. Battery
9. Battery Charge Indicator
10. Auxiliary Handle
11. 2-Pin Spanner
12. Cutting Guard
13. Backing Flange
14. Locking Flange
15. Grinding Guard
16. Spindle
17. Guard Clamp
18. Battery Charger
19. Red LED
20. Green LED
21. Charger Terminals
Intended Use
Hand-held, battery-powered angle grinder suitable for light to medium duty
grinding and cutting of metal and other materials with a fitted disc and
guard of the correct type. Suitable for wire brushing and sanding
applications with the optional purchases of compatible accessories.
The tool must ONLY be used for its intended purpose. Any use other than
those mentioned in this manual will be considered a case of misuse. The
operator, and not the manufacturer, shall be liable for any damage or injury
resulting from such cases of misuse. The manufacturer shall not be liable for
any modifications made to the tool, nor for any damage resulting from such
modifications.

Unpacking Your Tool

•
Carefully unpack and inspect your product. Fully familiarise
yourself with all its features and functions
•
Ensure all parts of the product are present and in good
condition
• If any parts are missing or damaged, have such parts
replaced before attempting to use this product

Before Use

WARNING: ALWAYS remove the battery before attaching or changing
any accessories, or making any adjustments.
Removing the Battery
To remove the Battery (8), press the Battery Release (7) and slide the
Battery out of the Battery Mount (6) (Fig. I (a-b))
Installing a charged Battery
1. To fit a charged Battery (8), slide it into the Battery Mount
(6) (Fig. I (c))
Note: The Battery will fit only in one direction, which is determined by its
shape and the design of the Battery Mount. However, if the Battery does
not slide into the Battery Mount easily, do not force it. Instead, pull the
Battery out of the Battery Mount again, check for correct position, and try
again gently.
2. Push the Battery into the Battery Mount until it locks into
place securely
Setting up the Charger
1. If fitted, remove the Battery (8) from the Battery Charger
(18) (Fig. II (b))
2. Connect the Battery Charger to the mains power supply
Note: The Green LED (20) on the Battery Charger will illuminate to indicate
that the Charger is powered.
WARNING: The Battery Charger is designed for indoor use only and
must not be exposed to moisture and rain.
Charging the Battery
WARNING: Failure to follow the correct procedure when charging the
Battery (8) will result in permanent damage.
Note: Normal charging time is 2 hours for a recently fully-discharged
Battery, but if the Battery has been left in a discharged state for some time,
it may take more time to charge.
1. Slide a discharged or partially discharged Battery onto the
Battery Charger (18) (Fig. II (a))
Note: Make sure the Battery and Battery Charger are lined up
correctly. If the Battery does not slide onto the Battery Charger
easily, don't force it. Instead, remove the Battery, then check that
the top of the Battery and the Battery Charger slot are clean and
undamaged and that the Charger Terminals (21) are not bent.
2. Once charging commences, only the Red LED (19) will
illuminate
Note: If the Red LED is not constantly illuminated after an
uncharged Battery is inserted into the Charger, the Battery or
Charger may be faulty. Recheck the Battery is fully inserted in the
Battery Charger. If the fault persists do not use and contact your
authorised Silverline distributer.
3. When the Battery is fully-charged, only the Green LED (20)
will be illuminated
Battery Charge Level
The Battery has a built-in Battery Charge Indicator (9). Pressing on the
button to the right will indicate the charge level. The number of bars that
illuminate when the button is pressed indicate the charge level; 1 bar
indicating a low charge, 3 bars indicating a full charge.
IMPORTANT: When a low charge level is indicated, be aware the tool may
stop operating while in use. This may be dangerous. It is recommended to
always ensure the Battery has a good charge level.
Notes about battery charging
IMPORTANT: Batteries are an expendable supply whose capacity shortens
over time. Always adhere to the correct handling and charging instructions
in the manual. If the battery does not hold charge or working time is
shortened, purchase a genuine Silverline replacement.
• The battery should be charged at ambient temperatures
between 10°C and 40°C (ideally around 20°C)
• After charging, allow 15 minutes for the battery to cool
before use
• Ensure that the charger is disconnected from the mains
supply after use, and is stored correctly
•
Do not leave batteries on charge for extended periods and
never store batteries on charge
•
The charger monitors battery temperature and voltage
while charging. Remove the battery once charging has been
completed to maximise charge cycles of the battery and not
waste power
silverlinetools.com
Original Instructions
11