Service And Warranty; Maintenance And Cleaning; Noise And Vibration - Dremel 8260 Bedienungsanleitung

When the Red warning LED will illuminate, you can
find detailed information and tips how to prevent this in
the Dremel App.
BLUETOOTH LED
The Bluetooth LED I indicates the tool is connected to
the smart device 7.
• The Bluetooth LED will repeatedly blink on the tool
as it attempts to connect to the smart device.
• Confirm connection of the tool to the smart device
by turning the variable speed dial G in either
direction 7.
• After completing this process you should see the
connected tool in the App and the Bluetooth LED
will be illuminated on the tool and will no longer
be blinking.
BATTERY LEVEL INDICATOR
3 of 3 solid green lights = 70-100% Charge remaining
2 of 3 solid green lights = 40-70% Charge remaining
1 of 3 solid green lights = 20-40% Charge remaining
1 of 3 flashing green lights = Below 20% charge remaining
Detailed battery charge information of your tool can be
found in the Dremel App.
Your tool is equipped with advanced electronics that
protect the Li-Ion cells in the battery from damage
due to excessive operating temperature and/or current
draw. If the lights illuminate red and/or the tool stops
working during heavy use, this most likely indicates
that the Li-Ion cells are near their maximum operating
temperature, and the battery pack should either be
changed or allowed to cool to ambient temperature
before continuing use. If the tool automatically turns off
due to overload conditions, the switch must be turned
off for a few seconds to allow the circuit to reset before
continuing use.
STALL PROTECTION
This tool has a stall protection feature built into it to
protect the motor and battery in the event of a stall.
If you put too much pressure on the tool for too long,
or bind the bit in a work piece, especially at high
speeds, the motor will stop. Simply take the tool
out of the material you were stalled in, and the tool
will begin to spin again at the selected speed. If the
tool continues to stall for longer than 5 seconds, the
tool will automatically shut itself off. This additional
feature further protects the motor and the battery from
damage. When the battery becomes close to empty,
the tool may shut down automatically more frequent
than normal. If this happens, it is time to recharge the
battery.

MAINTENANCE AND CLEANING

NO USER SERVICEABLE PARTS INSIDE.
!
PREVENTIVE MAINTENANCE PERFORMED
BY UNAUTHORIZED PERSONNEL MAY RESULT IN
INCORRECT CONNECTION OF INTERNAL WIRING
AND COMPONENTS WHICH COULD CAUSE
SERIOUS HAZARD.
The tool can be cleaned most effectively with
compressed dry air. Always wear safety goggles
when cleaning tools with compressed air.
TO AVOID ACCIDENTS, ALWAYS
!
DISCONNECT THE TOOL AND/OR CHARGER
FROM THE POWER SUPPLY BEFORE CLEANING
Ventilation openings and switch levers must be kept
clean and free of foreign matter. Do not attempt to
clean the tool by inserting pointed objects through an
opening.
Some of these are: gasoline, carbon tetrachloride,
chlorinated cleaning solvents, ammonia and household
detergents that contain ammonia.
We recommend that all tool service be performed by a
Dremel Service Centre.
This Dremel product is guaranteed in accordance with
7 statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling
are excluded from the warranty.
In case of a complaint, send the undismantled tool
and/or charger and proof of purchase to your dealer.
CONTACT DREMEL
For more information on service and warranty, the
Dremel product range, support and hotline, go to
www.dremel.com.
Sound pressure level (stand. deviation 3dB) dB(A) <70
Vibration (triax vector sum) m/s
Vibration uncertainty K m/s
NOTE: The declared vibration total value(s) and the
declared noise emission value(s) have been measured
in accordance with a standard test method and may be
used for comparing one tool with another; they may
also be used in a preliminary assessment of exposure.
The vibration emission during actual use of the power
tool can differ from the declared total value depending
on the ways in which you use the tool.
Make an estimation of the exposure in the actual
conditions of use and identify the safety measures for
personal protection accordingly (taking account of all
parts of the operating cycle such as the times when
the tool is switched off and when it is running idle in
addition to the trigger time).
The tool, batteries, accessories and packaging should
be sorted for environmental-friendly recycling.
Some regions require all E-waste to be collected
separately and disposed of in an environmentally
correct manner. Check E-Waste disposal regulations
and laws in your region prior to disposing the tool and
battery.
ONLY FOR EC COUNTRIES
According the European Guideline 2012/19/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that are
no longer usable must be collected separately and
disposed of in an environmentally correct manner.
25
CERTAIN CLEANING AGENTS AND
!
SOLVENTS DAMAGE PLASTIC PARTS.

SERVICE AND WARRANTY

NOISE AND VIBRATION

2
DISPOSAL
<2.5
2
1.5
6