Herunterladen Inhalt Inhalt Diese Seite drucken
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 17
that the overall dimensions of the hood and the hob ae
compatible with the cabinet and therefore the installation
is feasible.
Perform, in the back of the hob, a rectangular hole with
the following dimensions:
Hood 60cm Model: 542x100mm.
Hood 90cm Model: 842x100mm.
Hood 120cm Model: 1142x100mm
In case of version with motor already mounted, remove
the screws and the suction unit to insert the hood into the
hole made.
Install the hood in the hole made, inserting it from above,
as shown (Fig. 3). In case of version with motor on
board, it is necessary to remove the suction unit before
inserting the product into the cabinet.
Fix the hood inside the cainet using the special brackets
supplied (Fig. 4). Start mounting the brackets in the lower
part of the hood (Fig. 5a) making sure that there is a
distance of 2 mm between the lower part of the bracket
and the cabinet bottom (Fig. 5b). This distance allows
the traction of the product downwards on fixing, (Fig. 5c),
so that the stainless steel frame adheres perfectly on the
worktop.
Before inserting the screws into the cabinet, make sure
that the product is perfectly perpendicular to the worktop.
After completing the installation and connecting the
product to the power supply, lift the hood and remove the
door lock (Fig. 6).
In case of version with motor on board start mounting the
motor unit directing the air outlet to the chosen position
downwards or upwards (Fig. 7b). The motor can be
installed on both the front side and the back one of the
hood. Once the installationof the motor has been
comleted, start mounting the duct for the air outlet.
In case of version with external motor put the suction unit
(external motor) in a suitable area and arrange the air
outlet duct. Start mounting the air outlet duct between the
external motor and the hood. Select the air outlet among
the five possibilities (Fig. 7a) and install the union
supplied.
Put the metal box containing the electronic components
in an easily accessible area for any assistance
operations (Fig. 8), connecting the electric connectors of
the same to the hood: pushbutton panel connector (Fig.
9a), 9-pole connector (Fig. 9b), neon connector (Fig. 9c)
In case of installation with remote motor,connect the
power unit cable to the special connector placed on the
electronic components box (Fig.10a),and also connect
the 2-pole connector,if supplied (Fig.10b)
Connect the product to the power supply
All manuals and user guides at all-guides.com

Operation

Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
The hood is equipped with a "TOUCH" device to control the
lights and speed.
For the correct use please carefully read the intructions below.
The cooker hood can be controlled through a remote control
available as accessory kit (see the paragraph relating to the
functioning of the remote control).
Key T1: delays hood switching off timing the speed set
for some minutes.
By such function, when the timing is elapsed, the hood
switches off.
The timing is divided as follows:
• suction speed (power) 1: 20 minutes
• suction speed (power) 2: 15 minutes
• suction speed (power) 3: 10 minutes
• suction speed (power) 4: 5 minutes
PLEASE NOTE: When operating the timer, the hood
might switch to a lower intake speed (power) before
turning off, as on some speeds there is already a
timing on the speed reduction itself.
When keys T2 and T3 are pressed, the hood leaves the
timed function and the suction speed (power) increases
or decreases according to the key pressed. During the
timing phase the LED related to the corresponding speed
flashes.
Key T2: Decreases the active suction speed (power)
(4→3→2→1→OFF).
The speed is displayed through the LED related to the
corresponding speed.
Key T2 has no effect on the opening/closure of the
suction panel.
Key T3: Increases the active suction speed (power)
(1→2→3→4).
The speed is displayed through the LED related to the
corresponding speed.
Note: (only for models fitted with a motor or a remote
GME 22):
Suction speed 4 (power) is timed for 6 minutes, after
which the hood will automatically switch to suction speed
3 (power).
14

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis