Spare Parts List - FMS 1:18 Toyota FJ Cruiser Bedienungsanleitung

Spare parts list

C2092
1:18 FJ Cruiser Hood YELLOW
C2093 1:18 FJ Cruiser Front and Rear Light Cup Set
C2094 1:18 FJ Cruiser Hood Mount Set
C2095 1:18 FJ Cruiser Ladder And Spare Tire Bracket
C2096 1:18 FJ Cruiser Spotlight Cup Set
C2097 1:18 FJ Cruiser Rearview Mirror And Wiper
C2098 1:18 FJ Cruiser Bumper And Side Panel
C2099 1:18 FJ Cruiser Lens
C2100 1:18 FJ Cruiser Body SHELL YELLOW
C2101 1:18 FJ Cruiser Car Roof
C2045 Teraz Tire 19.2 x 13.5 x 56
C2046 1:18 Star Style Wheels plastic parts
C2052
FMS LIPO Battery 2S LIPO 380mAh
C2051 FMS USB Charger
C2049 1:18 050 Motor set
C2057 1:18 Plastic Gear set
C2058 1:18 Transmission Shaft full set
C2102 1:18 SCREW SET
CE Warning
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other transmitter. End-users and installers
must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF
exposure compliance.
Appendix 1 FCC Statement
FCC ID: 2AUBX-HT-TX02
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or televison reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this
equipment. Such modifications could void the user authority to operate the equipment.
1. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm
from all persons and must not be co-lacated or operating in conjunction with any other transmitter.End-users
and installers must be provided with antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance.
2. Move all your channels to the desired position.
3. Select [All channels] and then [Yes] in the confirmation box.
C2021 1:18 1KG High Torque 3wire Servo
C2103 1:18 FJ Cruiser Window
C2074 1:18 Rear Wheel Shaft
C2071
1:18 Wheel Hex
C2063 1:18 SHOCK PLASTIC PARTS
C2064 1:18 KATANA V2 / LC80 LAND CRUISER/
FJ Cruiser Connecting Rod
C2065 1:18 M4 ALLY BALL
C2066 1:18 BALL HEAD
C2067 1:18 Steering Hub & Spindle
C2068
1:18 FRONT/REAR AXLE parts
C2069 1:18 SERVO HORN
C2104 1:18 FJ Cruiser MIRROR LENS
C2075 1:18 FRONT OUTDRIVE SHAFT
C2076 1:18 Gear Box Plastic Parts
C2105 1:18 FJ Cruiser dash board SET
C2106 1:18 FJ Cruiser dash board seat SET
8
EN