Preparation Before Use; Starting And Stopping - Stanley FATMAX FMEG232 Bersetzt Von Den Originalanweisungen

Fitting and removing a grinding wheel (Fig B1,
B2, B3)
Warning! Do not use damaged grinding wheels.
Place the tool on a work bench, guard up.
u
Fit the inner flange (6) correctly onto the spindle (7)
u
(Fig. B1).
Place the disc (8) on the flange (6) (Fig.B2). When fitting
u
a disc with a raised center, make sure that the raised
centre (9) is facing the flange (6).
Screw the out flange (10) onto the spindle (7) (Fig. B3)
u
the ring on the flange (10) must face towoards the disc
when fitting a grinding disc (A)
the ring on the flange (10) must face away from the
disc when fitting a cutting disc (B)
Press the spindle lock (2) and rotate the spindle (7) until it
u
locks in position (Fig. B2).
Tighten the flange (10) with the two-pin spanner supplied.
u
Release the spindle lock.
u
To remove the disc, loosen the flange (10) with the two-pin
u
spanner.
Attaching the side handle (Fig C)
Warning! Before using the tool, check that the handle is
tightened securely.
Warning! The side handle should always be used to maintain
control of the tool at all times.
Screw the side handle (4) tightly into one of the holes (11) or
(12) on either side of the gear case.

Preparation before use

Attach the safety guard and appropriate abrasive or
u
grinding wheels. Do not use abrasive or grinding wheels
that are overly worn.
Make sure that the inner and outer flanges are attached
u
correctly.
Make sure that the abrasive or grinding wheels are
u
rotating in the direction of the arrows on the accessories
and tool.
Use
Warning! Always observe the safety instructions
and applicable regulations.
Warning! To minimize the danger of serious personal injury,
please switch off the tool power and disconnect all plugs
before adjusting or removing/installing any accessory. Before
reassembling the tool, press and release the trigger switch to
make sure the tool is already switched off.
Make sure all materials to be grinded are secured in
u
position.
Apply slight pressure to the tool. Do not apply side
u
pressure to the abrasive disc.
Avoid overloading. If the tool becomes hot, let it spin for a
u
few minutes with no load.
(Original instructions)
Be sure to hold the tool tightly with both hands (one hand
u
on housing, the other on side handle). Start the tool and
bring the grinding wheel on the workpiece.
Keep the edge of the wheel tilted at angle from 15 to 30
u
degrees against the surface of the workpiece.
When using a new grinding wheel, do not operate the
u
wheel in the B direction, otherwise, it will cut into the
workpiece. When the edge of wheel has been rounded off,
you are free to operate the grinder in either the A or B
direction.

Starting and stopping

Warning! Before using the tool, check whether the handle is
tightened securely. Check whether the ON/OFF switch is
working normally. Before plugging in the tool to the power
supply, check whether the switch is in the OFF position when
pressing the rear end of the switch.
To start the tool, press the rear end of the switch and slide it
forward. Then press the front end of the switch to lock it. Press
the rear end of the switch to stop the tool.
Warning! Do not switch the tool on or off while under load
conditions.
Proper hand position (Fig F)
Warning! To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
Warning! To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the side handle
(figure A), with the other hand on the body of the tool, as
shown in figure F.
Lock-Off feature of the switch
Slide trigger (1) to the front of the tool and then press the
trigger (1), the tool will start. Release the trigger (1), the tool
will stop running.
Explanation: Before coming into contact with the object you
are working on, make sure the abrasive wheel is turning at
maximum speed. Before turning off the tool, lift the tool up
from the object you are working on.
Caution: Make sure the abrasive wheel is completely
stopped before putting down the tool.
Rotating the gear case (Fig D)
The gear case is mounted onto the tool casing, and it can be
rotated to give the user a more comfortable experience while
cutting.
The rotating gear case can be turned 90 degrees, 180
degrees, and 270 degrees to the left or to the right.
Loosen the four screws on the gear case.
u
Rotate the gear case till it reaches its ideal location.
u
Tighten the four screws on the gear case.
u
Ensure that the rotating mechanism is locked.
u
ENGLISH
9