Maintenance - Makita LS0714 Bedienungsanleitung

the guide fence on the saw.
The finished piece to be used will
•
always be on the RIGHT side of the
blade after the cut has been made.
7. Cutting aluminum extrusion
Fig.42
When securing aluminum extrusions, use spacer
blocks or pieces of scrap as shown in the figure to
prevent deformation of the aluminum. Use a cutting
lubricant when cutting the aluminum extrusion to
prevent build-up of the aluminum material on the
blade.
CAUTION:
Never attempt to cut thick or round aluminum
•
extrusions. Thick aluminum extrusions may come
loose during operation and round aluminum
extrusions cannot be secured firmly with this tool.
8. Wood facing
Use of wood facing helps to assure splinter-free
cuts in workpieces. Attach a wood facing to the
guide fence using the holes in the guide fence.
See the figure concerning the dimensions for a
suggested wood facing.
Over 15mm (5/8") Over 420mm (16-1/2")
1
85mm 70mm 70mm
(3-3/8") (2-3/4") (2-3/4")
1. Holes
002206
CAUTION:
Use straight wood of even thickness as the wood
•
facing.
Use screws to attach the wood facing to the guide
•
fence. The screws should be installed so that the
screw heads are below the surface of the wood
facing.
When the wood facing is attached, do not turn the
•
turn base with the handle lowered. The blade
and/or the wood facing will be damaged.
9. Cutting repetitive lengths
Fig.43
When cutting several pieces of stock to the same
length, ranging from 220 mm to 385 mm, use of the
set plate (optional accessory) will facilitate more
efficient operation. Install the set plate on the holder
(optional accessory) as shown in the figure.
Align the cutting line on your workpiece with either
the left or right side of the groove in the kerf board,
and while holding the workpiece from moving,
move the set plate flush against the end of the
All manuals and user guides at all-guides.com
50mm-60mm
(2"-2-3/8")
27mm (1-1/16")
1
85mm
(3-3/8")
17
workpiece. Then secure the set plate with the screw.
When the set plate is not used, loosen the screw
and turn the set plate out of the way.
NOTE:
Use of the holder-rod
•
accessory) allows cutting repetitive lengths up to
2,200 mm approximately.
10. Groove cutting
Fig.44
A dado type cut can be made by proceeding as
follows:
Adjust the lower limit position of the blade using the
adjusting screw and the stopper arm to limit the
cutting depth of the blade. Refer to "Stopper arm"
section described on previously.
After adjusting the lower limit position of the blade,
cut parallel grooves across the width of the
workpiece using a slide (push) cut as shown in the
figure. Then remove the workpiece material
between the grooves with a chisel. Do not attempt
to perform this type of cut using wide (thick) blades
or with a dado blade. Possible loss of control and
injury may result.
CAUTION:
Be sure to return the stopper arm to the original
•
position when performing other than groove cutting.
Carrying tool
Fig.45
Fig.46
Make sure that the tool is unplugged. Secure the blade at
0° bevel angle and the turn base at the full right miter
angle position. Secure the slide poles so that the lower
slide pole is locked in the position of the carriage fully
pulled to operator and the upper poles are locked in the
position of the carriage fully pushed forward to the guide
fence. Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin.
Carry the tool by holding both sides of the tool base as
shown in the figure. If you remove the holders, dust bag,
etc., you can carry the tool more easily.
CAUTION:
Always secure all moving portions before carrying
•
the tool.
Stopper pin is for carrying and storage purposes
•
only and not for any cutting operations.

MAINTENANCE

CAUTION:
Always be sure that the tool is switched off and
•
unplugged before attempting to perform inspection
or maintenance.
assembly (optional