Product Handling - LUND 67572 Originalanleitung

GB
Recommendations for using the product
WARNING! The bowl and the housing may be hot after use. Do not touch them as it poses a risk of severe burns. Wait until the
product components cool down. If it is necessary to carry these elements before they cool down, grasp them only with handles
intended for that purpose. Use gloves that protect against the eff ects of high temperature.
Make sure that the fl oor next to the place where the product is used is not slippery. This will prevent the risk of slipping, which
may cause severe injuries.
The product may be plugged in only during operation. After it is fi nished, unplug the product, by removing the plug from the mains
socket. Do not leave the connected product unattended.
Food products placed in the bowl must not protrude above the bowl's maximum fi ll.
When preparing dishes, observe the product all the time. Foodstuff s remained unattended may be burned, which may cause a
fi re or severe burns.
The bowl should be carried only using the handle. The bowl has been fi tted with an insert with perforated bottom designed for
placing the food inside. Never use the bowl without an insert. The insert is mounted in the bowl by means of a latch hidden under
the movable housing. When carrying the bowl, always cover the latch with a housing. This will prevent accidental separation of
the bowl from the insert.
The latch may be released only when the bowl is placed on the ground.
Put the bowl with hot food only on the grand that withstands high temperature, or use protective stands.
While preparing the inside of the chamber and dishes themselves, you may touch them only with the use of tools made of such
materials that will withstand the temperature produced by the product. It is forbidden to use for this purpose your bare hands. Do
not use sharp, metal objects that may damage unstickable surface of the bowl and insert.
If any food waste remains during or after preparation of a dish inside the bowl or insert, it should be removed before preparing next
dish. Food waste may be burnt, thus generating a smoke, unpleasant odour, and also aff ect the taste of a meal prepared. They
may also cause a fi re. To remove it, use tools made of wood or plastics that withstand a temperature produced by the product. Do
not use sharp tools made of metal. Such tools may damage a surface of the bowl and insert.

PRODUCT HANDLING

Control panel
67572
The product is equipped with a touch control panel with an LED display and a knob/button.
When the product is connected to the power supply, a sound signal will be heard and all symbols will be briefl y highlighted, fol-
lowed by an indication on the display: "---". The product is in standby mode.
Touching the on/off switch or any button, or rotating or pressing the knob will activate the product's setting mode.
The display will show the default setting of temperature and time in minutes. To change the setting, use the knob, turn clockwise
to increase the setting, turn counter clockwise to decrease the setting. Each touch of the button is indicated by a sound signal and
a change in the display status.
Touching the button with the clock symbol allows you to change the time setting.
Touching the button with the thermometer symbol allows you to change the temperature setting.
By touching the "M" button, you can select one of the predefi ned operating modes by turning the knob. Each mode is a combina-
tion of time and temperature settings shown on the display. The operating modes can be changed in the following cycle: French
fries – ribs – shrimps – cake – poultry – meat – fi sh.
Caution! When programming the settings, the product automatically returns to standby mode approximately one minute after the
last touch of any button or rotation of the knob.
After setting the time and temperature in less than one minute, lightly press the knob. This will cause the device to begin operating.
This will be indicated by a fl ashing fan symbol. The fan symbol highlighted red indicates the operation of the product heater. The
fan symbol highlighted blue indicates that the fan is working.
The product can be turned off at any time by touching the on/off switch. After switching off , the fan can still work for some time,
accelerating the heater cooling process. Do not disconnect the product from the power supply during this time. When the cooling
of the heater is fi nished, the product will automatically switch to standby mode. The device power supply cord plug must then be
disconnected from the socket.
67573
The product's control panel includes two knobs and light indicator.
The upper knob is used for temperature setting.
The lower knob is used for time setting.
Lighting up of indicator indicates the heater operation. The product has been fi tted with inner temperature sensor. While operating
the indicator may switch in and off automatically.
The product may be disconnected at any moment by switching the time setting knob to "0".
O R I G I N A L I N S T R U C T I O N S
11