Maintenance And Storage - LUND 67090 Originalanleitung

GB
Telescopic pipe - a pipe of adjustable length, which allows for comfortable selection of working height. The length is adjusted by
pushing and holding the locking button and then changing the length. Releasing the pressure on the button and then slightly pull-
ing the pipe will trigger the lock and set the length of the pipe, and the sound of the ratchet mechanism will be heard.
Metal pipe - allows for telescopic pipe extension.
Floor and carpet brush - universal brush for cleaning both carpets and all types of hard fl oors. The brush is equipped with a lever
that allows the bristles to be pushed in and out. Pressing the lever in place of the bristle brush symbol pushes the bristles out.
Pressing the lever in place of the brush symbol without bristles pushes the bristles in.
Small brush - allows you to clean where a larger brush cannot fi t.
2 in 1 crevice brush - allows for cleaning in narrow crevices. The brush is equipped with rotating bristles.
Parquet brush - a brush equipped with rigid bristles. Used for cleaning hard fl oors. Soft bristles and wheels protect the fl oor against
scratching.
Pet hair brush - a brush designed for cleaning hair and fur from carpets and carpeting. The rotating bristles and the rotor inside
the brush allow for more eff ective cleaning of hair entangled in the carpet pile. The brush has a swivel cap with rigid bristles for
easy cleaning of long-pile carpets. The cap must rotated as far as it will go in the direction marked "DOWN" and then locked in this
position by means of a lock (XX). Unlocking and then rotating as far as possible in the direction marked "UP" raises the bristles.
When cleaning short-pile carpets, use a brush with the bristle raised.

MAINTENANCE AND STORAGE

CAUTION! Never immerse the vacuum cleaner in water or other liquids. Doing so may result in electric shock.
After cleaning, turn off the vacuum cleaner with the switch, disconnect the power cord plug from the socket, retract the cable,
disconnect the brush, pipe and hose and proceed with maintenance.
Disconnect the dust container from the vacuum cleaner. Open the lower cover of the container and discharge the waste collected
in the container. Open the top cover, remove both fi lters. Clean the container with a damp, soft cloth, then dry with a dry cloth or
allow to dry.
Remove the sponge fi lter from the upper fi lter and wash it under a stream of running, lukewarm water, squeeze out excess water
and leave the sponge to dry completely. Wait at least 24 hours after placing the fi lter in a well-ventilated place at room temperature.
Warning! It is forbidden to use the vacuum cleaner with a wet or damp fi lter. This can result in an electric shock.
The bottom fi lter can be rinsed under running, lukewarm water. Next dry with a dry cloth and allow to dry completely. Wait at least
24 hours after placing the fi lter in a well-ventilated place at room temperature.
Open the outlet fi lter cover by pressing the lock button (XIII). Remove the fi lter, the dirty fi lter can be washed under running,
lukewarm water or replaced with a new one. After cleaning, dry the fi lter thoroughly before reassembly. Wait at least 24 hours
after placing the fi lter in a well-ventilated place at room temperature. Check the fi lter seal for damage. Replace the fi lter with a
defective seal with a new one.
Install the fi lter as shown in the illustration (XIV). Secure the fi lter by attaching and snapping on the cover.
Do not wash fi lters in mechanical dishwashers and do not dry them with a stream of hot air. This can cause deformation of the
plastic material used for the construction of the fi lter. Avoid exposing the fi lters to direct sunlight.
No other part of the vacuum cleaner must be exposed to water. The non-woven part of the upper fi lter should be gently tapped,
shaking off larger impurities. In the case of excessive contamination, replace the fi lter with a new one.
Clean the remaining parts of the vacuum cleaner with a cloth slightly soaked in water, then dry or allow to dry.
Store the vacuum cleaner in a horizontal position. During storage, ensure that the hose is not bent, crushed or otherwise de-
formed. The hose can be connected or disconnected from the vacuum cleaner for storage. The vacuum cleaner has a hook at
the rear for attaching the fl oor and carpet brush (XV) for storage. Store the vacuum cleaner with the power cord rolled up and its
plug disconnected from the socket.
Cleaning the pet hair brush
Hair and fur can accumulate inside the brush, which reduces the eff ectiveness of the brush, therefore it is recommended to clean
the brush after each use.
Make sure that the lock is not locked in the bottom position. Unlock, if necessary. Use a fl at-head screwdriver or a small coin
to turn the cap lock (XVI) 90 degrees and remove the lock. Carefully pull away the side parts of the cap and remove it from the
brush (XVII). Turn the ring at the brush outlet in the UNLOCK direction and then move it towards the outlet. Carefully separate
the two halves of the brush housing. In the front part of the brush there are hooks (XVIII) which connect both parts of the casing,
be careful not to break them.
Slide the rotor and brush axis holders out of the guides in the top part of the housing.
The casing, brush, rotor and cap can be cleaned under running, lukewarm water and then thoroughly dried. For example, after
shaking the excess water off , wait at least 24 hours after placing all components in a well-ventilated place at room temperature.
After drying, assemble the brush in reverse order. Special attention should be paid to the correct installation of the brush and rotor
axis hooks (XIX). After assembling the brush, perform a test start. The rotor and the brush should rotate freely without creating
increased noise and/or vibrations. Repeat assembly, if necessary.
O R I G I N A L I N S T R U C T I O N S
14