Maintenance / Service; Declaration Of Conformity - Skil 2899 Allgemeine Originalbetriebsanleitung

• Spot light ^
Spot light J automatically lights on when activating switch
A 2
• Bit storage at the front &
• Additional bit storage *
- offers storage for 2 bits
- screw bit storage L on the right or the left of the tool
• Belt clip (
Screw belt clip M on the right or the left of the tool
• Holding and guiding the tool )
! while working, always hold the tool at the
grey-coloured grip area(s)
- keep ventilation slots P 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
APPLICAtION ADVICE
• When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
• When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking of
the wood
• For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
• When screwdriving in hard wood one should pre-drill a
hole

mAINtENANCE / SERVICE

• Keep tool and charger clean
- clean charging contacts in charger with alcohol or
contact cleaner
! unplug charger from power source before
cleaning
• If the tool/charger should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on www.skilmasters.com)
- in case of a defective charger send both charger and
battery to your dealer or the SKIL service station
ENVIRONmENt
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 8 will remind you of this when the need for
disposing occurs
All manuals and user guides at all-guides.com
• The battery must be kept separate from the natural

DECLARAtION OF CONFORmItY

• We declare under our sole responsibility that the product
• technical file at: SKIL Europe BV (PT-SEU/ENG1),
NOISE/VIBRAtION
• Measured in accordance with EN 60745 the sound
• The vibration emission level has been measured in
Perceuse/visseuse sans fil
INtRODUCtION
• Cet outil est conçu pour le perçage dans le bois, le métal,
10
environment and should not be disposed of as normal
domestic waste (symbol 9 will remind you of this when
the need for disposing occurs)
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
described under "Technical data" is in conformity with the
following standards or standardization documents: EN
60335, EN 61000, EN 60745, EN 55014, in accordance
with the provisions of the directives 2006/95/EC,
2004/108/EC, 2006/42/EC, 2011/65/EU, 2009/125/EC
(EU regulation 1194/2012)
4825 BD Breda, NL
18.12.2013
pressure level of this tool is 75 dB(A) and the sound
power level 86 dB(A) (standard deviation: 3 dB), and the
vibration ✱ (hand-arm method; uncertainty K = 1.5 m/s²)
✱ when drilling in metal <2.5 m/s²
✱ when screwdriving <2.5 m/s²
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
la céramique et les matières plastiques; les outils avec
réglage électronique de la vitesse et rotation à droite/à
gauche sont également appropiés pour le vissage et le
filetage
2899