Swfr Phase - Yamaha RX-V465 Bedienungsanleitung

Operating various settings for this unit (Setup menu)
Low-frequency components of other channel signals
Parameter Subwoofer
Both [1]
SWFR [4]
Front Not output
[1] Outputs low-frequency components of the front left and right
channels and the channel of speaker, the size of which is set to
"Small."
[2] Outputs low-frequency components of the front left and right
channels.
[3] Outputs low frequency components when the sizes of speakers
are set to "Large."
[4] Outputs low-frequency components of the channel of speaker,
the size of which is set to "Small."
Front
Small/Large*
Choices:
Sets the sizes of front left and right speakers.
Small
Select this when small speakers are
connected. Low-frequency components of the
front left and right channels are output from a
subwoofer.
Large
Select this when large speakers are
connected.
Note
• When "Bass Out" is set to "Front," you can only select "Large." If "Bass
Out" is changed to "Front," "Front" automatically switches to "Large"
even when it is set to "Small."
Center
Choices: None/Small*/Large
Sets the size of center speaker.
None
Select this when no center speaker is
connected. Center channel signals are spread
to front left and right speakers.
Small
Select this when a small center speaker is
connected. Low-frequency components of
center channel are output from a subwoofer.
If a subwoofer is not connected they are
output from front speakers.
Large
Select this when a large center speaker is
connected.
Sur. LR
Choices: None/Small*/Large
Sets sizes of left and right surround speakers.
None
Select this when no surround speakers are
connected. Surround channel signals are
spread to front left and right speakers.
"Sur.B" automatically switches to "None"
when this is selected.
42
En
Front Other
speakers speakers
[2] [3]
[3] [3]
[1] [3]
Small
Select this when small surround speakers are
connected. Low-frequency components of
surround channels are output from a
subwoofer. If a subwoofer is not connected
they are output from front speakers.
Large
Select this when large surround speakers are
connected.
y
• When "None" is selected, the sound field programs automatically enter
the Virtual CINEMA DSP mode.
Sur. B
None*/SMLx1/SMLx2/LRGx1/LRGx2
Choices:
Sets sizes of left and right surround back speakers. When
using the surround back speakers, connect an external
amplifier to the SURROUND BACK jacks of the PRE
OUT terminals.
None
Select this when no surround back speaker
are connected. Surround back channel signals
are output from the surround L/R speakers
and subwoofer. If the subwoofer is disabled,
they are output from the surround L/R
speakers and front speakers.
SMLx1
Select this when one small surround back
speaker is connected to an external amplifier
for the surround back speaker.
SMLx2
Select this when two small surround back
speakers are connected to an external
amplifier for the surround back speakers.
LRGx1
Select this when one large surround back
speaker is connected to an external amplifier
for the surround back speaker.
LRGx2
Select this when two large surround back
speakers are connected to an external
amplifier for the surround back speakers.
y
• When "None" is selected, "PLIIx Movie," "PLIIx Music," and "PLIIx
Game" cannot be selected.
Crossover
Choices: 40Hz/60Hz/80Hz*/90Hz/100Hz/110Hz/120Hz/
160Hz/200Hz
Sets the lower limit of the low frequency component
output from a speaker with a size set to "Small (SMLx1/
SMLx2)." Sound with a frequency below that limit is
output from a subwoofer or front speakers.
If your subwoofer has a volume control or a crossover
frequency control, set the volume to half or the crossover
frequency at the maximum.

SWFR Phase

NRM*/REV
Choices:
Sets the phase of your subwoofer if bass sounds are
lacking or unclear.
NRM
Select this not to change the phase of your
subwoofer.
REV
Select this to reverse the phase of your
subwoofer.