DeWalt DC411 Originalanweisungen Seite 62

EN GLI SH
• Never use blotters together with
bonded abrasive products.
• Be aware, the wheel continues to
rotate after the tools is switched off.
Proper Hand Position (fi g. 1, 9)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side
handle (e), with the other hand on the main
handle (q).
Switch
LOCK-OFF BUTTON AND TRIGGER SWITCH (FIG. 6)
Your cut-off tool is equipped with a lock-off button (b).
To lock the trigger switch, press the lock-off button
as shown. When the lock-off button is depressed to
the lock icon, the unit is locked.
Always lock the trigger switch when carrying or
storing the tool to eliminate unintentional starting.
To unlock the trigger switch, press the lock-off
button. When the lock-off button is depressed to the
unlock icon, the unit is unlocked. The lock-off button
is colored red to indicate when the switch is in its
unlocked position.
Pull the trigger switch (a) to turn the tool ON.
Releasing the trigger switch turns the tool OFF.
NOTE: This tool has no provision to lock the switch in
the ON position, and should never be locked ON by
any other means.
CAUTION: Hold the side handle and
body of the tool firmly to maintain
control of the tool at start up and during
use and until the wheel or accessory
stops rotating. Make sure the wheel has
come to a complete stop be fore laying
the tool down.
CAUTION: Allow the tool to reach full
speed before touching tool to the work
surface. Lift the tool from the work
surface before turning the tool off.
SPINDLE LOCK
The spindle lock pin is provided to prevent the
spindle from rotating when installing or removing
wheels. Operate the spindle lock pin only when the
tool is turned off, the battery is removed, and the
wheel has come to a complete stop.
60
NOTICE: To reduce the risk of damage
to the tool, do not engage the spindle
lock while the tool is operating. Damage
to the tool will result and attached
accessory may spin off possibly
resulting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate
the spindle further.
Mounting and Using Depressed
Centre Grinding Wheels
MOUNTING AND REMOVING HUBBED WHEELS (FIG. 1, 7)
WARNING: To reduce the risk of
serious personal injury, turn tool off and
remove battery pack before making
any adjustments or removing/installing
attachments or accessories.
Hubbed wheels install directly on the M14 threaded
spindle.
1. Thread the wheel on the spindle by hand.
2. Depress the spindle lock button and use a
wrench to tighten the hub of the wheel.
3. Reverse the above procedure to remove the
wheel.
CAUTION: Failure to properly seat
the wheel before turning the tool on
may result in damage to the tool or the
wheel.
MOUNTING NON-HUBBED WHEELS (FIG. 8)
WARNING: To reduce the risk of
serious personal injury, turn tool off and
remove battery pack before making
any adjustments or removing/installing
attachments or accessories.
Depressed centre Type 27 grinding wheels must be
used with included flanges.
1. Install the anti-lockup backing flange (g) on
spindle (d) with the raised centre against the
wheel. Be sure the backing flange recess is
seated onto the flats of the spindle by pushing
and twisting the flange before placing the
wheel.
2. Place wheel against the backing flange, centring
the wheel on the raised centre of the backing
flange.
3. While depressing the spindle lock button, thread
the clamp nut (h) on spindle. If the wheel you
are installing is more than 3.17 mm (1/8") thick,
place the threaded clamp nut on the spindle so
that the raised centre fits into the centre of the
wheel (Fig. 8A). If the wheel you are installing is