Block 3 Bedienmodul Premium - Cloos QINEO NexT Betriebsanleitung

Block 3 Bedienmodul PREMIUM

1. Hauptmenü .............................................................................................. 38
2. MAIN - Synergie ....................................................................................... 38
3. MAIN - Betriebsarten .............................................................................. 39
3.1 2-Takt ............................................................................................................................39
3.2 4-Takt ............................................................................................................................39
3.3 Super-4-Takt ..............................................................................................................40
3.4 Punkten ......................................................................................................................40
3.5 Extern...........................................................................................................................40
4. MAIN - Prozess .......................................................................................... 41
4.1 Elektrode ....................................................................................................................41
4.2 WIG ...............................................................................................................................41
4.3 Speed Weld ................................................................................................................41
4.4 Vari Weld ....................................................................................................................41
4.5 Control Weld .............................................................................................................41
4.6 Syn off ..........................................................................................................................42
4.7 Cold Weld ...................................................................................................................42
4.8 Rapid Weld .................................................................................................................42
4.9 Rapid Pulse Weld ....................................................................................................43
4.10 MoTion Weld ............................................................................................................43
5. MAIN - Funktion ...................................................................................... 43
5.1 DuoPulse ....................................................................................................................43
5.2 CleanStart ..................................................................................................................44
5.3 Ausblasen ..................................................................................................................44
5.4 Einfädeln (nur in Verbindung mit MoTion-Equipment) ......................44
5.5 Draht vor ....................................................................................................................44
5.6 Draht zurück .............................................................................................................44
5.7 Gas von Hand ...........................................................................................................44
5.8 Start von Hand ........................................................................................................45
5.9 Aus / Neustart .........................................................................................................45
6. MAIN - Programmieren .......................................................................... 45
6.1 Parameter in den Betriebsarten 2-Takt und 4-Takt .................................46
6.2 Parameter in der Betriebsart Super-4-Takt .................................................47
6.3 Parameter in der Betriebsart Punkten / Intervall ....................................48
6.4 MAIN - Programmieren - Stellbereiche ........................................................49
6.4.1 Eingabe der Stellbereiche .............................................................................................. 49
6.4.2 Voraussetzung zur Nutzung der Stellbereiche ................................................... 50
6.4.3 Deaktivieren der Stellbereiche .................................................................................... 51
6.5 MAIN - Programmieren - Tandem ...................................................................52
6.6 MAIN - Programmieren - Impulssync. ..........................................................52
6.7 MAIN - Programmieren - Expert Mode .........................................................52
6.7.1 Expert Mode - Rücksetzen auf Synergiewerte ..................................................... 53
6.7.2 Hauptparameter im "Expert Mode" ......................................................................... 53
6.7.3 Schweißparameter im "Expert Mode" ..................................................................... 54
6.7.4 "DuoPulse-Parameter" im "Expert Mode" .............................................................. 54
6.8 Main - Programmieren - Aktiver QWD .........................................................55
6.9 Main - Programmieren - Nebenparameter (ab V.x.4.x) .........................55
6.9.1 Aktiven Schweißkreis festlegen .................................................................................. 55
6.9.2 Rangierstrecke festlegen (optional) ......................................................................... 55
7. MAIN - Messwerte ................................................................................... 56
7.1 Betriebsdaten ...........................................................................................................56
7.1.1 Datensatzumschaltung 1/2 ......................................................................................... 57
7.1.2 Setup Nahtzähler .............................................................................................................. 58
7.1.3 Verbrauchskosten ............................................................................................................. 58
8. MAIN - Anzeige ........................................................................................ 59
9. MAIN (2) - Konfig (Konfiguration) ........................................................ 61
9.1 Konfig - Allgemein .................................................................................................61
9.1.1 Displayhelligkeit ................................................................................................................ 62
9.1.2 MHW x10 Master .............................................................................................................. 62
9.1.3 Steuerung Kühlmittelpumpe und Lüfter ............................................................... 62
9.1.4 Konfig - Allgemein - Grundeinstellungen ............................................................. 63
9.1.4.1 Konfig - Allgemein - Grundeinstellungen - Tandem ......................................... 64
9.1.5 Konfig - Allgemein - Grundeinstellungen (2) ....................................................... 64
9.1.6 Konfig - Allgemein - Sense-Technik ........................................................................... 65
9.1.7 Konfig - Allgemein - QWD ............................................................................................. 65
9.1.7.1 Konfig - Allgemein - QWD - QWD-B .......................................................................... 66
9.1.7.2 Konfig - Allgemein - QWD - QWD Push-Pull ......................................................... 67
9.1.8 Konfig - Allgemein - SD-Modul ................................................................................... 67
9.1.9 Konfig - Allgemein - Optionen .................................................................................... 67
35