Description Of The Safety Devices And Warning Labels; Identification Plate; Hydraulic Valve Adjustment; Daily Inspection - AJ Easy Roller Gebrauchsanleitung

2.3 Description of the safety devices and warning labels

Fig.3: Safety- and warning labels
A. Operating instruction sticker
B. Sticker to read this instruction
C. Identification plate (ID- plate)
D. Capacity sticker (both sides/ sample, for illustration only, capacity
might be different for your type)
E. Sign warning stay clear stop truck (only US- market)
F. Sign prohibited use (only US- market)
The safety and warning labels should be placed according to figure 3. The
advices on the truck are additional to this handbook. Please follow the operating
instructions. If the decals are damaged or missing, please replace them. Your
truck might be optional equipped with a parking brake or with a progressive
parking and drive brake. How to use this kind of brakes is described in chapter
6.

2.4 Identification plate

Fig. 4: ID-Plate
1. Designation, type
2. Serial number
3. Rated capacity
4. Eventually company logo
5. Name and address of the manufacturer
6. Net weight
7. Manufacturing date
8. Option, Wheel combination, fork length, width over the forks
9. Place of CE mark
3. WARNING AND SAFETY INSTRUCTIONS
DO NOT
• Allow other person then the operator to stand in front of or behind the
truck when it is moving or lifting/lowering.
• Overload the truck.
• Put foot in front of rolling wheel, Injury could result.
• Use the truck on a slope or inclined surface, the truck may become
uncontrollable and create danger.
• Lift or carry people. People could fall down and suffer severe injury.
• Use truck with unstable, unbalanced loosely stacked load.
• Use the truck in explosive atmospheres.
Watch difference in floor levels when moving the truck. Load could fall down or
the truck could get uncontrollable. Keep watching the condition of load. Stop
operating table if load becomes unstable.
Practice maintenance work according to regular inspection. This truck is not
designed to be water resistant, therefore use it in dry atmospheres.

4. HYDRAULIC VALVE ADJUSTMENT

On the tiller of your pallet truck, you will find the control lever, which
can be regulated in three positions:
Lower : handle up, the lever moves back to the neutral, when released
Neutral: handle in center position
Raise: handle down
If necessary, you can adjust the lever according to following steps.
a) If the forks elevate while pumping in the Neutral position, turn the adjusting
nut on the adjusting bolt clockwise until pumping action does not raise the forks
and the Neutral position works properly.
b) If the forks descend while pumping in the Neutral position, turn the adjusting
nut counter-clockwise until the forks do not lower.
c) If the forks do not descent when the control handle is in the Lower position,
turn the adjusting nut clockwise until raising the control handle lowers the forks.
Then check the Neutral position and be sure that the adjusting nut is in the
proper position.
d) If the forks do not elevate while pumping in the Raise position, turn the
adjusting nut counter- clockwise until the forks elevate while pumping in the
Raise position. Then check the Lower and Raise position.

5. DAILY INSPECTION

This chapter describes pre-shift checks before putting the truck into operation.
Daily inspection is effective to find the malfunction or fault on the truck and can
maximize the lifetime. Check the truck on the following points before operation.
Remove load from truck and lower the forks to the lowest position.
DO NOT USE THE TRUCK IF ANY MALFUNCTION OR FAULT IS FOUND.
• Visually check for structural deformation or cracks of arms, forks, or any other
component, and unusual noise or binding of the lifting mechanism.
• Check if there is any oil leakage.
• Check the vertical creep of the lifting mechanism.
• Check the smooth movement of the wheels.
• Check if there are any particles or damages on the wheels.
• Check if all the bolts and nuts are tightened firmly.
• If equipped, check the brake.
• Verify that all labels are in place.
• Check and grease the EASY ROLLER
5 | 01-2811700 • ajproducts.ie