Adjusting The Bevel Angle - Makita LS0714 Bedienungsanleitung

CAUTION:
• When turning the turn base, be sure to raise the
handle fully.
• After changing the miter angle, always secure
the turn base by tightening the grip firmly.

Adjusting the bevel angle

► Fig.16: 1. Lever 2. Release button
► Fig.17: 1. Pointer 2. Bevel scale 3. Arm
To adjust the bevel angle, loosen the lever at the rear of
the tool counterclockwise.
Push the handle to the left to tilt the saw blade until the pointer
points to the desired angle on the bevel scale. Then tighten
the lever clockwise firmly to secure the arm.
To tilt the blade to the right, push the release button at
the rear of the tool while tilting the blade slightly to the
left after loosening the lever. With the release button
depressed, tilt the saw blade to the right.
CAUTION:
• When tilting the saw blade, be sure to raise the handle fully.
• After changing the bevel angle, always secure
the arm by tightening the lever clockwise.
• When changing bevel angles, be sure to posi-
tion the kerf boards appropriately as explained
in the "Positioning kerf boards" section.
Adjusting the lever position
► Fig.18: 1. Lever 2. Screw
The lever can be repositioned at every angle 30° when
the lever does not provide full tightening.
Loosen and remove the screw that secures the lever at the rear of
the tool. Remove the lever and install it again so that it is slightly
above the level. Secure the lever with the screw firmly.
Switch action
WARNING:
Before plugging in the tool,
always check to see that the switch trigger actu-
ates properly and returns to the "OFF" position
when released. Do not pull the switch trigger hard
without pressing in the lock-off button. This can
cause switch breakage. Operating a tool with a
switch that does not actuate properly can lead to loss
of control and serious personal injury.
WARNING:
NEVER use tool without a fully
operative switch trigger. Any tool with an inoper-
ative switch is HIGHLY DANGEROUS and must be
repaired before further usage or serious personal
injury may occur.
WARNING:
NEVER defeat the lock-off button
by taping down or some other means. A switch with
a negated lock-off button may result in unintentional
operation and serious personal injury.
WARNING:
NEVER use the tool if it runs when
you simply pull the switch trigger without press-
ing the lock-off button. A switch in need of repair
may result in unintentional operation and serious
personal injury. Return tool to a Makita service center
for proper repairs BEFORE further usage.
► Fig.19: 1. Switch trigger 2. Lock-off button 3. Hole
for padlock
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
A hole is provided in the switch trigger for insertion of a
padlock to lock the tool off.
WARNING:
or cable any smaller than 6.35 mm in diameter. A
smaller shank or cable may not properly lock the tool
in the off position and unintentional operation may
occur resulting in serious personal injury.
Lighting up the lamps
For model LS0714F, LS0714FL
► Fig.20: 1. Light 2. Light switch
CAUTION:
• This is not a rainproof light. Do not wash the light in
water or use it in a rain or a wet area. Such a conduct
can cause an electric shock and fume.
• Do not touch the lens of the light, as it is very hot
while it is lighted or shortly after it is turned off.
This may cause a burn to a human body.
• Do not apply impact to the light, which may
cause damage or shorted service time to it.
• Do not keep casting the beam of the light to your
eyes. This can cause your eyes to be hurt.
• Do not cover the light with clothes, carton, card-
board or similar objects while it is lighted, which
can cause a fire or an ignition.
Push the upper position of the switch for turning on the
light and the lower position for off.
Move the light to shift an area of lighting.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of
lamp. Be careful not to scratch the lens of light,
or it may lower the illumination.
Laser beam action
For model LS0714FL, LS0714L
► Fig.21: 1. Switch for laser
CAUTION:
• Never look into the laser beam. Direct laser
beam may injure your eyes.
• LASER RADIATION, DO NOT STARE INTO THE
BEAM OR VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS, CLASS 2M LASER PRODUCT.
To turn on the laser beam, press the upper position (I) of the
switch. Press the lower position (O) to turn off.
Laser line can be shifted to either the left or right side of the
saw blade by adjusting the adjusting screw as follows.
► Fig.22: 1. Adjusting screw
1. Loosen the adjusting screw by turning it
counterclockwise.
2. With the adjusting screw loosened, slide the
adjusting screw to the right or left as far as it goes.
16 ENGLISH
Do not use a lock with a shank