Eurosystems MLT 01 Bedienungsanleitung Seite 19

START
STOP
Accelerator command. In the START po-
sition, the air is open; while, in the STOP
position, the motor is off.
LEFT – the lever under the handlebar
activates the forward movement of the
wheels.
RIGHT – the lever moved upward acti-
vates the equipment.
(IF AVAILABLE)
LEFT - the lever on the right of the han-
dlebar activates the wheels backward
movement.
RIGHT - the lever on the left of the han-
dlebar activates the wheels forward
movement.
DANGER!
Keep all labels clean and in good condi-
tion, replace them if damaged.
4. TECHNICAL FEATURES
GROSS and NET
CE declaration label on
weight
the last page
Rated power
Width
Depends on the tool
Length 1120 mm
Height 1080 mm
510 mm
Path
*
13x5.00-6
Pneu
*
2.5 km/h
Forward speed
*
Reverse speed 3.3 km/h
Sound power CE declaration label on
Acoustic pressure the last page of the tool
Vibrations
manual
* Model with forward gear only
** Model with reverse and forward gears
5. HANDLING AND PACKAGING
2 or more people are required to handle
packaging, using the handles on the card-
board box. The GROSS weight is indicated
in the "TECHNICAL FEATURES" chapter.
CAUTION!
Do not overturn or roll the machine. Pos-
sible damage to bonnets and mechanical
parts.
INFORMATION!
If more than one machine or interchange-
able equipment is supplied on pallets,
unload without dropping them on the
ground. Use a forklift if necessary.
6. UNPACKING/ASSEMBLY
1. 1 1. 2
1. 7
1. 6
Complete the assembly by installing the in-
terchangeable equipment chosen following
the assembly instructions contained in the
specific manual.
DANGER!
Both springs must be correctly engaged
for the brake system to function properly.
DANGER!
If one or both springs break, replace
them before using the machine.
CAUTION!
The motor is supplied without lubricating
oil. For information on the type of oil and
quantities to be used, refer to the motor
manual contained in the accessory bag
[C]. 1.1
CAUTION!
Do not start the engine until all assembly
560 mm
stages have been completed.
**
13x6.00-6
CAUTION!
**
Add lubricating oil to the motor before
2.5 km/h
first start-up. For information on the type
**
of oil and quantities to be used, refer to
the motor manual contained in the ac-
cessory bag [C].
Before starting the machine, check the
oil level inside the motor, as indicated in
the specific user's manual
Before proceeding, read and understand
the chapter "SAFETY INSTRUCTIONS"
in its entirety.
Use caution when handling flammable
fluids. Fuel is highly flammable and ex-
plosive.
Do not fill the tank in closed or poorly
ventilated environments.
Before refilling the tank, switch off the
machine and wait until the motor has
1. 4 1.5 cooled down (15-20 min).
1.3
1.8
Do
ic devices near combustible fluids.
Use suitable, undamaged filling devices
such as fuel cans, funnels, etc.
In case of fuel leakage, move the ma-
chine before starting it up.
When filling operations have been com-
pleted, replace the cap and tighten it
firmly.
7. USE
Check correct functioning of the main-
tained action levers and double safety
command before using the machine. See
the "CABLE ADJUSTMENT" paragraph
to make adjustments. It is forbidden to
use the machine in case of malfunction
of the controls.
Check the motor oil level before starting
the machine.
1.1
If the engine is "cold", operate the start-
CAUTION!
.
DANGER!
7.1 TANK FILLING
DANGER!
DANGER!
DANGER!
DANGER!
not smoke or use electron-
DANGER!
DANGER!
DANGER!
3 .1
7.2 START-UP AND SHUT-DOWN
DANGER!
CAUTION!
INFORMATION!