Inhaltsverzeichnis; Optional Accessories; ): 9.0 M/S; Uncertainty (K): 1.5 M/S - Makita HR4003C Betriebsanleitung

(For model HR4003C) Loosen the six screws and
remove the handle. (Fig. 22)
(For model HR4013C) Loosen the eight screws. And
remove the guard cover as shown in the figure. And then
remove the handle. (Fig. 23 and 24)
Remove the connector by pulling it. (Fig. 25)
Loosen the screws and remove the change lever.
Remove the crank cap cover. (Fig. 26)
Remove the control plate. (Fig. 27)
Loosen the six screws and remove the crank cap. Rest
the tool on the table with the bit end pointing upwards.
This will allow the old grease to collect inside the crank
housing. (Fig. 28)
Wipe out the old grease inside and replace with fresh
grease (30 g). Use only Makita genuine hammer grease
(optional accessory). Filling with more than the specified
amount of grease (approx. 30 g) can cause faulty
hammering action or tool failure. Fill only with the
specified amount of grease.
Reinstall all removed parts. (Fig. 29)
Attach the connector and reinstall the handle. (Fig. 30)
NOTE:
• Note that the different lengths of screws are used.
NOTICE
• Do not tighten the crank cap excessively. It is made of
resin and is subject to breakage.
• Be careful not to damage the connector or lead wires
especially when wiping out the old grease or installing
the handle.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• SDS-Max Carbide-tipped bits
• SDS-Max bull point
• SDS-MAX cold chisel
• SDS-MAX scaling chisel
• SDS-MAX tile chisel
• SDS-MAX clay spade
• Hammer grease
• Bit grease
• Side handle
• Side grip
• Depth gauge
• Blow-out bulb
• Safety goggles
• Carrying case
• Dust extractor attachment
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Model HR4003C
Work mode: chiseling function with side handle
Vibration emission (a

Uncertainty (K): 1.5 m/s

Work mode: chiseling function with side grip
Vibration emission (a
Uncertainty (K): 1.5 m/s
Work mode: hammer drilling into concrete
Vibration emission (a
Uncertainty (K): 1.5 m/s
Model HR4013C
Work mode: chiseling function with side handle
Vibration emission (a
Uncertainty (K): 1.5 m/s
Work mode: chiseling function with side grip
Vibration emission (a
Uncertainty (K): 1.5 m/s
Work mode: hammer drilling into concrete
Vibration emission (a
Uncertainty (K): 1.5 m/s
• The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to
the trigger time).
ENG905-1
): 92 dB (A)
pA
): 103 dB (A)
WA
ENG900-1
2

): 9.0 m/s

h,CHeq
2
2
): 9.0 m/s

h,CHeq

2
2
): 10.0 m/s
h,HD
2
2
): 4.5 m/s
h,CHeq
2
2
): 4.5 m/s
h,CHeq
2
2
): 5.0 m/s
h,HD
2
ENG901-1
9