Functional Description - Makita GF600 Bedienungsanleitung

A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
8.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject to
the Dangerous Goods Legislation requirements.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specified by Makita. Installing the batteries to
non-compliant products may result in a fire, exces-
sive heat, explosion, or leak of electrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
Overview of the nailer
► Fig.1: 1. Battery cartridge 2. Fuel cover 3. Trigger
4. Indication lamp 5. Pusher button 6. Pusher
lever 7. Magazine 8. Contact element
9. Lamp 10. Exhaust vent
FUNCTIONAL
DESCRIPTION
CAUTION:
• Always be sure to remove the fuel cell, the
battery cartridge and nails before adjusting or
checking function on the tool.
Installing or removing battery cartridge
CAUTION:
• Always switch off the tool before installing or
removing of the battery cartridge.
• Hold the tool and the battery cartridge firmly
when installing or removing battery car-
tridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your
hands and result in damage to the tool and
battery cartridge and a personal injury.
► Fig.2
To install the battery cartridge, hold it so that the battery
cartridge front shape fits to that of the battery install-
ment opening and slip it into place. Insert it all the way
until it locks in place with a little click.
► Fig.3: 1. Button
To remove the battery cartridge, withdraw it from the
tool while pressing the buttons on the side of the car-
tridge as shown in the figure.
CAUTION:
• Always insert the battery cartridge all the way
until it locks in place. If not, it may accidentally
fall out of the tool, causing injury to you or some-
one around you.
• Do not install the battery cartridge forcibly. If the
cartridge does not slide in easily, it is not being
inserted correctly.
Lighting up the lamp
CAUTION:
• Do not look in the light or see the source of light
directly.
► Fig.4: 1. Lamp button
To switch on the Lamp, press the lamp button. To switch
off the lamp, press the lamp button again.
Fuel cell
Attaching the metering valve to the
fuel cell
► Fig.5: 1. Metering valve 2. Cap
Detach the cap (in case the metering valve is provided
with the cap).
► Fig.6
Push in the front edge.
► Fig.7
Push in the rear edge until it seats.
10 ENGLISH