Keytis Remote Control Description; Keygo Remote Control Description; Fitting The Battery For Keytis Remote Controls; Programming Keytis Remote Controls - Fig. 18 To - SOMFY DEXXO PRO io Installationsanleitung

Dexxo Pro io
[3]. Adjust the closed position using the "+" or "-" buttons.
Release the "-" button before the motor has time to force against
the door.
[4]. Press "OK" to validate the closed end limit position and start the self-
learning cycle.
The door runs through a complete Open Close cycle.
- If learning was correct, the display will show "C1".
- If the learning cycle was not completed correctly, the display will show
"S1".
During the learning cycle:
- If the door is moving, pressing any button will stop the movement and interrupt
the learning mode.
- If the door is stopped, pressing "SET" once will exit the learning mode.
You can call up the learning mode at any time, even when the learning cycle
has already been executed and the display shows "C1".
At the end of installation, it must be checked that the obstacle detection
complies with annex A of the standard EN 12 453.

4.3 Keytis remote control description

1 - Individual control buttons
2 - General STOP button
3 - General CLOSE button (Keytis 4 home io only)
4 - Operation indicator light On
5 - Low battery indicator light
6 - Closing clip
7 - PROG button: programming the transmitter
8 - KEY button: memorising the system key

4.4 Keygo remote control description

1 - Individual control buttons
2 - Operation indicator light
On

4.5 Fitting the battery for Keytis remote controls

4.6 Programming Keytis remote controls - Fig. 18 to 22

If the installation already comprises other io-homecontrol® products
with at least one programmed remote control
then you must perform the Memorising the system key step before
programming the remote controls (Fig. 19).
If the Keytis io remote control to be programmed is the system's first
remote control, then go straight to Programming the
Keytis remote control step (Fig. 20 to 22).
7
WARNING
Intermittent Blinking
Intermittent Blinking
The operations for memorising the system key and to program a
remote control by copying another Keytis remote control are only
possible at the installation location. To gain authorisation to transfer
its system key or its programming, the previously programmed
remote control must be able to establish radio communication with
an installation receiver.
> Memorising the system key (Fig. 19).
[1]. Set existing remote control no. 1 to the key transfer mode:
- With a Keytis, Telis, Impresario, Composio remote control: press the
"KEY" button until the green indicator comes on (two seconds).
- With another remote control: refer to its documentation.
[2]. Briefly press the "KEY" button on the new remote control. Wait for the
confirmation beep (a few seconds).
> Programming the Keytis remote control (Fig. 20 to 22)
Before programming the remote control, make sure that it has already
memorised the system key.
Each control button is programmed individually.
A button that is already programmed cannot be programmed on a second
receiver. To see if a button is already programmed, press it:
- button programmed → green indicator comes on..
- button not programmed → orange indicator comes on.
To clear a previously programmed button, refer to the section on Clearing
Keytis remote controls.
There are two ways to program the remote control:
- Programming from a Dexxo Pro motor.
- Programming by copying a previously programmed Keytis remote
control.
> Programming from a Dexxo Pro motor (Fig. 20)
[1]. Press the "PROG" button on the Dexxo Pro until the light comes on (two
seconds).
[2]. Briefly press the "PROG" button on the remote control.
Wait for the second beep and for the green indicator to start blinking
quickly.
This may take from a few seconds to around a minute depending on the
number of products connected to the system.
[3]. Briefly press the button chosen to control the Dexxo Pro motor.
The remote control sounds a confirmation beep and the Dexxo Pro
motor's light blinks for five seconds.
> Programming by copying a previously programmed Keytis
remote control
Completely copy the programming of a Keytis remote control (Fig. 21)
This operation is used to copy all of the buttons programmed from an already
programmed remote control.
[1]. Press the "PROG" button on the previously programmed remote control
until the green indicator comes on (two seconds).
[2]. Briefly press the "PROG" button on the new remote control.
Wait for the second beep and for the green indicator to start blinking
rapidly (a few seconds).
Individually copy the programming of a Keytis remote control button
(Fig. 22)
This operation is used to copy the programming of a single button from an
already programmed remote control.
[1]. Press the "PROG" button on the previously programmed remote control
until the green indicator comes on (two seconds).
[2]. Briefly press the button to copy on the previously programmed remote
control.
[3]. Briefly press the "PROG" button on the new remote control.
Wait for the confirmation beep (after a few seconds).
[4]. Briefly press the button chosen to control Dexxo Pro on the new remote
control.
Copyright © 2015 SOMFY ACTIVITES SA. All rights reserved