Operation; Working Advice - Texas HTR 1600 Bedienungsanleitung

Operation

Trigger gun. See Fig. 15
The trigger gun is equipped with a trigger lock
to prevent accidental activation. Use the trigger lock
when the cleaner is not in use, when it is being left
unattended, or when setting the product down to avoid
accidental operation.
1. Activate the trigger lock by pressing the lock button
located closest to the trigger on the bottom of the
grip.
2. Deactivate the trigger lock by pressing the unlock
button located further back on the bottom of the
grip to start operation again
Testing the machine, the first time
1. Fully assemble the product and attach attachments
to the lance
2. Connect water supply hose to product
3. Turn water supply on
4. Make sure the on/off switch located at the front of
the machine is on "O" (OFF)
5. Insert the plug into a correct voltage power
outlet/socket
6. Turn the on/off switch to "I" (ON)
7. Deactivate the trigger lock by pressing the unlock
button
8. Direct the nozzle away from yourself and others
9. Hold the trigger gun with both hands firmly
10. Press the trigger, a water jet sprays out of the
nozzle
11. Release the trigger to stop the spray
12. Activate the trigger lock by pressing the lock button
to lock the trigger into its off position
13. Turn the on/off switch to "O" (OFF)
14. Turn water supply off
General operation and safety
•
Always check the product, the electric cable, the
plug and the accessory for damage beofre use.
•
Check one more time, that the accessory is fixed
properly to the trigger gun/lance.
•
Always hold the product in the trigger gun and
lance. NEVER hold on the nozzle.
•
Check that the cooling grooves on the backside of
the product is clean and unblocked. Clean them if
necessarry with a soft brush and remove bigger
obstacles. Blocked cooling grooves kan cause
overheating and damage the product.
Start
1. Assembly the product as instructed.
2. Hold the trigger gun/lance firmly with both hands.
3. Point the nozzle away from yourself and others and
towards the surface that should be cleaned.
4. Activate the trigger and point the water jet against
the surface that should be cleaned.
5. Keep a suitable distance between lance and the
work area that should be cleaned, so the surface
will not be damaged. When working on less robust
surfaces, it is recommended to incease the
distance.
6. Release the trigger gun to stop the water jet.
3-in-1 nozzle. See Fig. 16+17
This high pressure cleaner are supplied with a smart 3-
in-1 nozzle, with the following functions:
• A powerful rotating turbo jet
A 20 flat jet for softer cleaning
• o
En 0 o pencil jet for extra hard cleaning
•
Turn the nozzle end to the wanted position.

Working advice

High pressure cleaning of objects and surfaces,
and choice of water jet is done at own risk and
responsibility. It is up to user to ensure that the
object and surface is suitable for high pressure
cleaning!
General
•
Ensure that the machine is on level ground.
•
Do not overreach with the high pressure hose or
move the machine by pulling thehose, this could
cause the machine to become unstable and fall.
•
Do not kink og drive a motor vehcle over the high
pressure hose.
•
Do not expost the high pressure hose to sharp
edges or corners.
The 0 o pensil jet is the hardest water jet. Be very careful
when using it, as it can damage the object that is
beging cleaned. This also partly counts for the turbo jet.
Always start cleaning with the 20
enough, consider to use the turbo jet with bigger
distance to the object.
ikke er nok.
Never use the turbo jet or pencil jet to clean
motor vehicles. It might damage the surface!
Working advice for cleaning with detergents
Only use cleaning substances suitable specifically
•
for high presure cleaners.
We recommend that you use detergent sparingly for the
sake of the environment. Observe the recommended
dilution on the detergent label.
Cleaning vertical walls
1. Best results are obtained by dissolving the dirt by
first applying a detergent mixed with water to the
surface, while it is still dry.
2. Leave the detergent on the surface for 1-3 minutes,
but do not allow the detergent to dry.
20
o flat jet, and if not