Specifications - EGO BC3800E Bedienungsanleitung

MAINTENACE AND STORAGE
EN
◾
Disconnect the machine from the power supply
(i.e. remove the battery pack) before carrying out
maintenance or cleaning work.
◾
Use only the manufacturer's recommended
replacement parts and accessories.
◾
Inspect and maintain the machine regularly. Have the
machine repaired only by an authorized repairer.
◾
When not in use, store the machine out of the reach
of children.
OTHER SAFETY WARNINGS
◾
Avoid Dangerous Environments – Don't use
appliances on damp or wet slope.
◾
Keep guards in place and in working order.
◾
Keep hands and feet away from the cutting area.
◾
To reduce the risk of injury, never work on a ladder
or on any other insecure support. Never hold the
cutting unit above waist height.
◾
Check the cutting unit at regular short intervals
during operation, or immediately if there is a
noticeable change in cutting behavior.
◾
For best results, your battery should be charged in a
location where the temperature is greater than 5° C
and less than 40° C. Do not store it outside or in vehicles.
◾
If you are approached, stop the motor and cutting unit.
◾
Warn the operator of the danger of blade thrust
(only using with 3-teeth blade).
◾
Blade thrust may occur when the spinning blade
contacts an object that it does not immediately cut.
◾
Blade thrust can be violent enough to cause the unit
and/or operator to be propelled in any direction, and
possibly lose control of the unit.
◾
Blade thrust can occur without warning if the blade
snags, stalls or binds.
◾
Blade thrust is more likely to occur in areas where it
is difficult to see the material being cut.
◾
Do not attach any blade to a unit without proper
installation of all required parts. Failure to use the
proper parts can cause the blade to fly off and
seriously injure the operator and/or bystanders.
Discard blades that are bent, warped, cracked,
broken, or damaged in any way. Use a sharp blade
A dull blade is more likely to snag and thrust
(only using with 3-teeth blade).
◾
A coasting blade/line can cause injury while it
continues to spin after the motor is stopped or
trigger is released. Maintain proper control until
the blade/line has completely stopped rotating.
10
56 VOLT LITHIUM-ION REAR MOTOR BIKE-HANDLE BRUSH CUTTER — BC3800E
◾
Use only with battery packs and chargers listed in
fig.A.
◾
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
even when the tool is not operating. Take care when
performing maintenance or service.
◾
Do not wash with a hose; avoid getting water in
motor and electrical connections.
◾
If situations occur that are not covered in this
manual, use care and good judgment. Contact the
EGO Customer Service Center for assistance.
SAVE THESE INSTRUCTIONS!

SPECIFICATIONS

Cutting unit Trimmer head
Voltage
56 V
Recommended
Operating
Temperature:
Recommended
Storage Temperature:
No-load Speed 4500-6000 /min 4500-6000 /min
2.4mm nylon
Cutting Line Type
twist line
Cutting blade /
Cutting Width 38 cm
Weight (without
4.43 kg
battery pack)
Measured sound 94.4 dB(A)
power level L K=1.6 dB(A)
WA
Sound pressure level at 80.9 dB(A)
operator's position L K=2.5 dB(A)
PA
Guaranteed sound
power level L
96 dB(A)
WA
(measured according
to 2000/14/EC)
Left 2.32 m/s
handle K=1.5 m/s
Valuation of
vibration a
Right 1.78 m/s
h
handle K=1.5 m/s
◾
The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another;
3-teeth metal
blade
56 V
0°C-40°C
-20°C-70°C
/
ABB1203
30 cm
4.64 kg
94.04 dB(A)
K=1.71 dB(A)
80.0 dB(A)
K=4.1 dB(A)
96 dB(A)
2 1.55 m/s 2
K=1.5 m/s
2 2
1.88 m/s
2 2
K=1.5 m/s
2 2