Fm Radio Operation - Trevi HCV 10D35 DAB Bedienungsanleitung Und Anschluss

Seite von 51

/ 51
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

ENGLISH

Manual tune: allows you to manually scan a single DAB/DAB+ frequency. Press the TUNE

to select the channel number relating to the frequency to be scanned and then press the ENTER (24) button to start the scan.

The stations found will be automatically memorized. At the end, long press the MENU button (21) to return to the DAB menu.

DRC: allows you to enable/disable the DRC function to improve the sound when listening in noisy environments. The DRC level

can be set to high, low or OFF.

Prune (Delete): allows you to delete from the list of stored stations all the radios found but not available or with scarce

signal. Use the TUNE

Time: allows you to set the current time/date.

Set Time/Date: set the current time and date.

Auto Update: select from which source to automatically set the time and date if available.

Set 12/24 Hour: set the time format 12/24H.

Set Date Format: set the date format.

Factory Reset: allows you to restore the appliance's factory settings. After the restoration is complete, an automatic scan of

the DAB/DAB+ stations will be performed. Move with the TUNE

ENTER (24).

SW version: allows you to view the device's software version.

STORING STATION PRESETS

It is possible to store up to 10 of your favourite stations to the preset keys:

1. Tune in to the desired radio station;

2. Hold MEMORY button (35) for 2 seconds, then press PRESET

3. Use PRESET

button (22) and PRESET

4. Press ENTER button (24) to confirm and save the radio station. Repeat this for each radio station you wish to save. 10 memory

locations are available;

5. To recall a stored radio station, press the relevant numeric button (34) or press MEMORY button (35) then PRESET

(22) or PRESET

button (25) key to scroll the list. Press ENTER button (24) to confirm and start playback of the chosen station.

Note: to recall a station stored on location 10, press the "0" button.

DAB/DAB+ DISPLAY MODE

Every time you press the INFO button (37) on the remote control, the display will cycle through the following display modes:

DLS (dynamic label segment): Dynamic label segment is a scrolling message that the broadcaster may include with their transmis-

sions . This message usually includes information, such as program detail etc...

Signal strength: This option will display a bar indicating the signal strength.

Program type: This describes the "Style" or "genre" of music that is being broadcast e.g. "Rock "or "Classical".

Ensemble/Multiplex (group name): A multiplex/ensemble is a collection of radio stations that are bundled and transmitted on one

frequency. There are national and local multiplexes. Local ones contain stations that are specific to that area.

Channel frequency: Displays the current DAB multiplex in use.

Signal error index: displays information relating to the level of signal errors and the intensity with which it is received.

Bit Rate: displays information related to the compression ratio of the current transmission.

Time: displays the time signal received by the radio station.

Date: displays information about the date.

1. Switch on the appliance and press the

FM/DAB button (18) on the remote control;

2. Press and hold TUNE

or previous radio station with the best signal received;

3. To optimize the frequency, press TUNE

frequency by 0.05MHz and perform a step-by-step search;

4. To activate the automatic station search and storage function, keep the SCAN (49). pressed for a few seconds. The device is

capable of storing up to 10 stations;

5. To store a radio station, refer to the paragraph "Storing station preset" in the DAB section.

Note: To obtain the best FM reception, connect and orient the antenna. If the reception is not good, try to adjust the length and

orientation of the antenna, however the quality of FM reception depends a lot on the place where the device is placed.

(23) and TUNE

(48) button to move to Y (YES) and confirm the deletion with ENTER button (24).

button (25) to select a memory location;