Operation; Emergency Operation; Test Operation; Air Flow Direction Adjustment - Haier AS09FBAHRA Bedienungsanleitung

Operation

Base Operation
Remote controller
1. Unit start
Press ON/OFF on the remote controller, unit star ts.
2. Select operation mode
COOL button:Cooling mode
HEA T button: Heating mode
DRY button: Dehumidify mode
3.Select temp.setting
button
Press
Every time the button is pressed, temp.setting
increase 1 o C,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting
decrease 1 o C,if kept depressed, it will
decrease rapidly
Select a desired temperature.
4.Fan speed selection
PressFAN button. For each press, fan speed
changes as follows:
Remote controller:
LOW MED HI
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
Remote
Operation
Mode
Controller
Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according to
AUTO
room temperature. When FAN is set to AUTO the air
conditioner automatically adjusts the fan speed according
to room temperature.
COOL
In DRY mode, when room temper ature becomes lower
DRY
than temp .setting+2
speed regardless of FAN setting.
In HEAT mode, warm air will blow out after a short
period of the time due to cold - draft prevention function.
HEA T
When FAN is set to AUTO, the air conditioner automatically
adjusts the fan speed according to room temperature.
In FAN operation mode , the unit will not operate in COOL or
HEAT mode but only in FAN mode, AUTO is not available in
FAN
FAN mode. And temp. setting is disabled. In FAN mode,
sleep operation is not available.
2
3
4
4
3
Display
circulated
AUTO
Note
C, unit will run intermittently at LOW
o
Emergency operation and test operation

Emergency Operation:

Use this operation only when the remote controller is defective
or lost, and with function of emergency running, air conditoner
can run automatically for a while.
When the emergency operation switch is pressed, the " Pi "
sound is heard once, which means the start of this operation.
When power switch is turning on for the first time and
emergency operation starts, the unit will run automatically in
the following modes:
Room Timer
Designated Fan
temperature mode
temperature speed
Above 23 o C 26 o C AUTO
No
o o
Below 23 C 23 C AUTO
No
It is impossible to change the settings of temp. and fan speed,It
is also not possible to operate in timer or dry mode.

Test operation:

Test ope ration switch is the same as emergency switch.
Use this switch in the test operation when the room
o
temperature is below 16 C, do not use it in the
normal operation.
Continue to press the test operation
switch for more than 5 seconds . After
you hear the "Pi" sound twice, release
your finger from the switch: the cooling
operation starts with the air flow speed "Hi".
Under this operation mode,the fan motor of indoor
unit will run in high speed.

Air Flow Direction Adjustment

1.Vertical flap
Pos.1
Pos.2
Pos.3
Pos.4
(Autoswing)
Pos.5
2.Press button. changes as follows:
Press button again , vertical flap will stop over
present position, the swing function will be cancelled
button to choose the Pos.2 and Pos.3.
3.Press
4.
For each press of "
displays as follows:
remote controller:
Initial state
When humidity is high, condensate water might occur
at air outlet if all vertical louvers are adjusted to left or
right.
position for a long time in COOL or DRY mode,
otherwise, condensate water might occur.
better air circulation
Operation
mode
COOL
Pi
HEA T
Pi
Remote controller
COOL/DRY/AUTO(Initial state):
HEAT(Initial state):
(no)
Pos.4
" button, remote controller
2