Advice On Chimney-Sweeping And Stove And Smoke Flue Maintenance; Sweeping; Usual Cleaning - deville C07923 Installations- Und Gebrauchsanleitung

Small speed, selector 12 in position I.
Big speed, selector 12 in position II.
Let the appliance heat.
Choose the automatic running (A) or manual (M) with
the selector 13.
In M position : forced on and off of the vent. This
position allows a immediate starting of the blower and
asks for a manual stop.
In A position : automatic working of the vent quand
when the appliance is completely hot, generally in the
hour that follows the lighting. Its running is stopped
the appliance is cold, generally at the extinction of the
fire.
To enjoy both the immediate starting and the automatic
stop, use the M position at the ligting stage, then
change to A position once the appliance is hot. It will
stop automatically in that case.
7 - ADVICE ON CHIMNEY-SWEEPING AND
STOVE AND SMOKE FLUE MAINTENANCE

7.1 - Sweeping:

The mecanical sweeping of the smoke flue is
compulsory, it has to be made a few times a year and
one sweeping has to done during the heating period. A
certificate has to be established by the professional.
For sweepings, you'll need to :
•
Remove the deflector (Fig. 23) :
- Dismantle the deflector
if forward.
- Let the back part of the du deflector
and take it out.
- To put the deflector back: proceed in the reverse
way of the dismantling.
•
Check thoroughly the condition of the appliance
paying special attention
elements : seals and locking components, support
parts (door, frame).
•
Check the condition of the smoke flue and the
connecting pipe : all the connections must show
good mecanical holding and must have kept their
smoke-tight features.
•
Vacuum the inside of the hood to avoid any
accumulation of dust ; clear if necessary the hot air
convection route..
If you detect any irregularities : have your appliance or
your installation repaired by a professional.
7.2 – Cleaning , maintenance of the vent
- Dismantling of the blower (Fig.22) :
Remove the 2 screws
blower.
Take out the blower in drawing the grate.
-Reassembling of the blower:
Proceed in the reverse way of the dismantling.
- Electric plan (Fig. 21)
by lifting it and drawing
go down
to smoke-tightness
from the fixing of the
7.3 – Usual cleaning
•
Clean the window with a wet cloth and ash. If
necessary use
respecting the instructions for use : start the
cleaning once the appliance is completely cold.
•
Clean regularly the secondary air intake part (Fig.
24).
- Vacuum
the air guide and the window glass. If necessary
slip a thin blade or a sheet of rigid cardboard
between the air guide and the glass to make the
cleaning easier (clearing of the particles).
These particles block the making of the secondary
air flow which protects the widow from the direct
contact with smokes and complete the the burning
of the wood.
- Scrape off with the end of a metallic object
inferior edge of the air intake part to remove the
bistre which has settled there.
These operations have to be made as soon as the
window glass is dirty and it is essential to wait for
the complete extinction of the fire within the
appliance to implement them.
If some local and distinct soot patches (Fig. 24)
appear again and multiply, it is necessary to
dismount the air guide to make a more complete
cleaning (Fig. 25) :
. Hang the door out and lay it down.
. Remove the 3 screws.
. Remove the air guide A and clean it.
. Reassemble the whole and check that the
original window kit is respected.
This operation has to be performed by a skilled
professional.
•
Clean regularly the hot air releases grilles of the
hood.They get filled in all the more easily as their
meshing is thin : choose a suitable frequency of
cleaning.
•
Check the efficiency of the latch of the door and if
necessary make the following adjustments (Fig.
26) :
- Harden the closing of the door:
. Proceed successively through the loosening
of the screw
. Give the 2 screws a quarter turn and do it
again if necessary.
NOTA : This operation increase the pressure on
the smoke-tight seal of the door of the appliance.
- Loosen the closing of the door:
. Proceed successively through the loosening
of the screw
. Give the 2 screws a quarter turn and do it
again if necessary.
NOTA : This operation decrease the pressure on
the smoke-tight seal of the door of the appliance.
22
a specific cleaning
dust and the particles stuck between
and the screwing down of
and the screwing down of
product
the
.
.