Before Commissioning; Assembling The Equipment; Saw Blade Guard - Scheppach Parkside PMTS 210 A1 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

NOTE:
The specified device emissions values have been measured in
accordance with a standardised test procedure and can be
used for comparison of one electric tool with another.
The specified device emissions values can also be used for an
initial estimation of the load.
WARNING:
The noise emission values can vary from the specified values
during the actual use of the electric tool, depending on the
type and the manner in which the electric tool is used, and in
particular the type of workpiece being processed. Implement
measures to protect against noise nuisance. In doing so, take
into account the complete working process, including the times
when the electric tool is working without load or switched off.
Suitable measures include regular maintenance and care of the
electric tool and the insertion tools, regular breaks as well as
proper planning of the working process.

8. Before commissioning

• Open the packaging and carefully remove the device.
• Remove the packaging material, as well as the packaging
and transport safety devices (if present).
• Check that the delivery is complete.
• Check the device and accessory parts for transport damage.
• If possible, store the packaging until the warranty period has
expired.
m WARNING
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!
• The equipment must be securely installed, i.e. bolted down
on a workbench, base frame or similar. Use the holes on the
inner side of the frame legs for this.
• Prior to commissioning, all covers and safety devices must be
mounted correctly.
• It must be possible for the blade to run freely.
• In case of previously machined wood, be aware of any for-
eign bodies, such as nails or screws, etc.
• Before you press the On/Off switch check that the saw
blade is fitted correctly. Moving parts must run smoothly.
• Before you connect the equipment to the power supply make
sure the data on the rating plate are identical to the mains
data.
• Connect the equipment to a properly installed protective
contact socket, with at least 16 A circuit breaker.

9. Assembling the equipment

m WARNING:
Disconnect the mains power plug before maintaining, resetting
or assembling the table saw.
9.1 Before assembling the equipment
• Place all parts supplied on a flat surface.
• Group equal parts.
NOTE:
• If compounds with a bolt (round head / or hexagon), hex
nuts and washers are backed up, the washer must be fitted
under the nut.
• Insert screws each from outside to inside. Secure connections
with nuts on the inside.
• Tighten the nuts and bolts during assembly only to the extent
that they can not fall down. If you tighten the nuts and bolts
prior to final assembly, final assembly can not be performed.
9.2 Fitting the table width extension (fig. 4-6)
1. Loosen the knurled screws (26) (Fig. 5).
ATTENTION:
Do not unscrew the knurled screws (26) too far.
2. Feed the guide tubes (23) of the table width extension
(22) into the guide bushings (27) (see Fig. 4/5).
3. Slide the end pieces (24) into the guide tubes (23) of the
table width extension (22) as shown in Fig. 6.
4. Fasten the end pieces (24) with the screws (25) as shown
in Fig. 6.
5. Pull the table width extension (22) out completely and
fasten in place with the knurled screws (26) (Fig. 5).
6. Now fold out the support feet (30).
7. Align the table width extension (22) horizontally with the
table saw.
8. Loosen the lock nuts (29) on the respective support foot
(30) and adjust the height adjustment screw (28) as re-
quired.
9. Then retighten the lock nuts (29).
If you do not need the table width extension (22), fold the sup-
port feet (30) in.

9.3 Saw blade guard

9.3.1 Fitting/removing the saw blade guard (Fig. 7)
1. Loosen the wing nut (4a) of the saw blade guard (4) and
slide the carriage bolt (4b) in the guide so that the thinner
part of the pin is exposed in the opening.
2. Place the saw blade guard (4) onto the riving knife (3)
from above so that the pin sits firmly in the recess of the
riving knife (31).
3. Slide the pin into the guide so that the carriage bolt (4b)
engages in the opening provided for it.
4. Turn the wing nut (4a) clockwise to secure the saw blade
guard in the correct position.
5. Ensure that the saw blade guard (4) can move freely.
6. Disassembly takes place in reverse order.
m WARNING
Danger of injury due to incorrectly mounted saw blade guard
• Before starting sawing, ensure that the saw blade guard (4)
lowers automatically onto the material to be sawn.
9.3.2 Checking the saw blade guard
After fitting, check that the saw blade guard (4) is functioning
properly.
1. Lift the saw blade guard (4) and then release it.
2. The saw blade guard should automatically move back to
its starting position.
GB/IE 25