Additional Functions; After Ironing; Cleaning And Maintenance - ROWENTA DX9200 Bedienungsanleitung

Innenteil - DX9200
The power steam and vertical steam functions (E 4) are
also possible if the steam control is set to
between bursts of steam should be about two seconds.
Important:
Never direct the steam at persons or animals!
E5 Spray function
To dampen stubborn creases, press the spray button.
F

Additional functions

F1 Anti-Drip system
Prevents water escaping from the soleplate when the
temperature is too low.
F2 Anti-scale system
Your iron contains an anti-scale cartridge to reduce scale
deposits. This considerably prolongs the operational life
of your iron. The anti-scale cartridge is an integral part of
the water tank and need not be replaced.
Do not use descaling agents, as these damage the lining of
the steam chamber and so may impair the steam function.
F 3 Automatic electronic 3-position cut-out (depending on
model)
If, although switched on, the appliance is not moved, it
will automatically switch off after the following intervals:
After 30 sec., if the iron is standing on the soleplate or
lying on its side.
After 8 mins., if the iron is standing on its heel.
The LED display starts to flash yellow-green-red in regular
sequence. If the appliance is moved, it will automatically
switch on again and begin to heat up again.
G

After ironing

• Unplug from the mains, pour away remaining water
and set steam control to
cool down.
• Store the iron standing on its heel.
• Do not wind the cord round the hot soleplate.
H

Cleaning and maintenance

When the appliance has cooled down, wipe it down with
a damp cloth or sponge, as required.
Dirt can be removed from the soleplate with a damp
cloth or sponge. Do not use sharp or abrasive cleaning
agents or objects.
Important: If the appliance has been standing unused for
long periods, hold it horizontal and allow it to emit
steam for approx. 1 minute to clean the steam ducts and
remove any residue from the iron.
4
Downloaded from www.Manualslib.com
18.02.2003 9:51 Uhr Seite 4
. The interval
. Then allow the appliance to
manuals search engine
I
Problems?
Problems Possible cause
The iron is plug- No mains supply.
ged in, but the
soleplate of the
iron remains cold.
The soleplate is The temperature
not heating up control is set too
properly. low.
LED „Traffic Light" Temperature con-
display does not trol set to "0".
light up.
None or too little There is insuffi-
steam is being cient water in the
emitted. water tank.
Anti-Drip is active
(F1).
All 3 colours of The automatic cut-
the Traffic Light out has activated:
display flash the appliance is
alternately. on standby.
The traffic Light The temperature
display flashes sensor in the sole-
red fast. plate is defective.
Brown streaks You are using che-
come through the mical descaling
holes in the sole- agents.
plate and stain
You linen is not
the fabric.
rinsed sufficiently
or you have ironed
a new garment
before washing it.
The soleplate is You are using a too
dirty or brown high temperature.
and can stain the
You are using
linen.
starch.
The soleplate is You have placed
scratched or your iron flat on a
damaged. metallic rest-plate.
You have ironed
over a zip.
If you have any further problems or queries with our products
please call our Customer Relations team first for expert help and
advice:
HELPLINE:0845 602 1454 – UK, 01 4751947 – Ireland
If you are unable to trace the cause of the fault, contact an
official Rowenta Customer Service Centre. The addresses are
shown in the enclosed service centre address list. Further hints
and tips are obtainable from our homepage: www.rowenta.com.
In line with a policy of continuous product improvement
Rowenta reserves the right to change product specifications
without prior notice.
Solution
Check that the mains plug is
properly inserted or try
plugging the iron into a dif-
ferent socket.
Set the temperature control
to a higher temperature (D).
Turn the temperature control
to the required setting.
Fill the water tank (C).
Wait for the soleplate to reach
the correct temperature.
If moved, the appliance will
switch on again.
Call our Customer Relations
Helpline – see below
Do not add any descaling
agents to the water in the
water tank.
Ensure linen is rinsed
thoroughly to remove any
soap desposits or chemicals
on new garments which may
be sucked up by the iron.
See the temperature table to
correctly set the thermostat.
Clean the soleplate as indi-
cated above. Always spray
starch onto the reverse side
of the fabric to be ironed.
Always set the iron on its
heel.
Try to avoid ironing over zips
which may have rough edges.
5