Safety Devices; Symbols On The Device; Initial Start-Up - Kärcher K 7 Premium Smart Control Originalbetriebsanleitung

**KÄRCHER suction hose for water supply from
31
open containers (order no. 2.643-100.0)
* optional, ** additionally required
LCD display
Illustration C
Area of application (1-SOFT / 2-MEDIUM / 3-HARD
1
with 2 pressure levels each)
BOOST function indicator
2
Spray type recommendation (flat stream/detergent/
3
dirt grinder)
®
Display Bluetooth connection
4
Signal strength status (four levels)
5
Battery status (empty, almost empty, medium, full)
6
Detergent level (1 / 2 / 3)
7

Safety devices

CAUTION
Missing or modified safety devices
Safety devices are provided for your own protection.
Never modify or bypass safety devices.
Power switch
The power switch prevents unintentional operation of
the device.
High-pressure gun lock
The lock locks the lever of the high-pressure gun and
prevents the device from starting unintentionally.
Auto-stop function
If the lever of the high-pressure gun is released, the
pressure switch turns off the pump and the high-pres-
sure jet stops. The pump switches on again when the le-
ver is pressed.
Motor circuit breaker
The motor circuit breaker shuts off the device if power
consumption it too high.

Symbols on the device

Do not aim the high-pressure jet may at per-
sons, animals, live electrical equipment or
the device itself.
Protect the device against frost.
The device may not be connected to the pub-
lic drinking water network.
Assembly
For the illustrations, refer to the graphics page.
Fit the supplied loose parts onto the device before start-
ing up the device.
Mounting the accessory net
1. Hang the accessory net on the hooks.
Illustration D
Push the high-pressure hose through the
hose guide
1. Insert the high-pressure hose through the hose
guide from the rear.
Illustration E
Installing the water connection coupling
1. Screw the water connection coupling onto the water
connection on the device.
Illustration F

Initial Start-Up

Note
If you do not want to control the device by mobile device
®
via a Bluetooth connection, you only have to follow the
steps in the section "Connecting the high-pressure
gun".
Download the app and register your device
1. Download the KÄRCHER Home & Garden app (see
chapter KÄRCHER Home & Garden app).
2. Start the KÄRCHER Home & Garden app.
3. Log in to the KÄRCHER Home & Garden app. If
necessary, create an account for this.
4. Scan the enclosed QR code.
The high-pressure cleaner is registered.
Note
If you do not have the enclosed QR code at hand, you
can also register the device with the part number and
serial number. Both numbers are given on the type
plate.
5. Follow the instructions of the KÄRCHER Home &
Garden app.
Note
Be sure to do this before connecting the high-pressure
®
gun Bluetooth Activate on your mobile device.
Connecting the high-pressure gun
Note
You can find a detailed description of the connection at
https://www.kaercher.com/FCR.
6. Plug the mains plug for the high-pressure cleaner in-
to a socket.
The device switches to coupling mode for 60 s. Dur-
ing this time it is possible to couple the high-pres-
sure gun.
7. Press the "+" key and the "-" key on the high-pres-
sure gun simultaneously for at least 3 s.
If the coupling is successful, the pressure levels, as
well as the radio and the Bluetooth
shown on the display.
Illustration G
The Bluetooth
vice and the high-pressure cleaner is established
automatically.
Note
If necessary, you can also establish the Bluetooth
nection at a later time by pressing the "-" key for 10 s.
8. If the coupling attempt failed:
a Pull the mains plug for the high-pressure cleaner
out of the socket.
b Wait 20 s.
c Couple the high-pressure gun again.
Initial startup
Note
Take care not to exceed the maximum permissible
mains impedance at the connection point (see chapter
Technical data).
Contact your electricity supplier in the case of any un-
certainties regarding the mains grid impedance at your
electrical connection point.
1. Place the device on a flat and level surface.
2. For devices with a hose reel: Completely unwind the
high-pressure hose from the hose reel.
3. For devices without a hose reel: Unwind the high-
pressure hose completely and eliminate any loops
and twists.
4. Pull the high-pressure hose all the way forwards
through the hose guide.
English
®
symbol, will be
®
connection between the mobile de-
®
con-
15