Operation - Makita DLS600 Betriebsanleitung

contents, tapping it lightly so as to remove particles
adhering to the insides which might hamper further
collection. ►
Fig.41:
nozzle 3. Fastener
NOTE: If you connect a vacuum cleaner to your saw,
cleaner operations can be performed.
►
Fig.42
Securing workpiece
WARNING:
It is extremely important to always
secure the workpiece correctly with the vise.
Failure to
result
injury
and/or the workpiece.
WARNING:
When cutting a workpiece that is
longer than the support base of the saw, the
material should be supported the entire length
beyond the support base and at the same height to
keep the material level. Proper workpiece support
will help avoid blade pinch and possible kickback
which may result in serious
Do
on
and/or horizontal vise to secure the workpiece. Thin
material tends to sag. Support workpiece over its
entire length to avoid blade pinch and possible
KICKBACK.
►
Fig.43: 1. Support 2. Turn base
Vertical vise
WARNING:
Secure the workpiece firmly
against the turn base and guide fence with the
vise during all operations. Otherwise the material
may move during the cutting operation, cause
damage to the blade, and be thrown which may
result in loss
serious
Install the vertical vise on either the left or right side of
the guide fence. Insert the vise rod into the hole in the
guide fence and tighten the lower screw to secure the
vise rod.
►
Fig.44: 1. Vise arm 2. Vise knob 3. Guide
fence
4. Turn base 5. Lower screw 6. Upper screw
7. Vise rod
Position the vise arm according to the thickness and
shape of the workpiece and secure the vise arm by
tightening the upper screw. If the upper screw contacts
the guide fence, install the upper screw on the opposite
side of vise arm. Make sure that no part of the tool
contacts the vise when lowering the handle fully. If
some part contacts the vise, re-position the vise. Press
the workpiece flat
1. Dust bag 2. Dust
do so may
in serious personal
and cause damage to the tool
personal injury.
not rely solely
the vertical vise
of control and
personal injury.
against the
guide fence
Position the workpiece at the desired cutting position
and secure
tightening the
Attaching the shoulder strap
Optional accessory
CAUTION:
Be sure to remove the shoulder
strap before operating the tool. The shoulder
strap may be entangled and cause injury.
CAUTION:
Be sure to attach the hooks of the
shoulder strap to the tool securely. If the hooks
are attached incompletely, they may come off and
cause injury.
The shoulder strap is convenient for transporting the
tool. Attach the hooks of the shoulder strap to the tool
as shown
►
Fig.45:

OPERATION

WARNING:
Make sure the blade is not
contacting the workpiece, etc. before the switch
is turned on. Turning the tool on with the blade in
contact with the workpiece may result in kickback and
serious personal
WARNING:
After a cutting operation, do not
raise the blade until it has come to a complete
stop. The raising of a coasting blade may result in
serious personal
to
NOTICE:
Before use, be sure to release the
handle from the lowered position by pulling the
stopper pin.
NOTICE:
Do not apply excessive pressure on the
handle when cutting. Too much force may result in
overload of
decreased cutting
down handle with only as much force as necessary
for
without
speed.
NOTICE:
Gently press down the handle to
perform the cut. If the handle is pressed down with
force or if lateral force is applied, the blade may
vibrate and leave a mark (saw mark) in the workpiece
and the precision of the cut may be impaired.
Press cutting (cutting small
workpieces)
►
Fig.46
30 ENGLISH
and the
it firmly
vise knob.
in the
1. Shoulder strap 2. Hook
injury.
injury and
the workpiece.
the motor
efficiency. Press
smooth cutting
significant decrease in blade
turn base.
by
figure.
damage
and/or
and