Preparing Cappuccino - Oursson EM1500 Bedienungsanleitung

UTILIZATION
Control panel, Рiс. С-3
- Steam button with yellow indication
- Coffee brewing button with green indication
- ON/OFF button with red indication
Steam control switch, Рiс. С-6
- OFF
- Steam supply
Preparation for operation
Before first use, сwipe the body of the device
soft, dry cloth. Remove the nozzle from the steam pipe
by slightly turning it around the axis. Wash it with warm
water and wipe dry. Water tank, tank's lid, filters
3
, filter holder , measuring spoon
wash with warm water and detergent. Dry all the parts.
Before assembling or disassembling the device,
make sure that the device is unplugged.
Before first use, clean the entire system for the first time,
run 350-400 ml. of water without using coffee. For that,
open the lid and fill the water tank to the MAX. Use only
clean water at room temperature 25°C. Plug in the device.
Before turning on the coffee machine, make sure
that the steam control switch is in (OFF) position,
and and
Install the filter holder (without coffee), Pic. D-4. Press
, button, red indication will turn on. Place a cup under the
filter holder's spout.
Press . button. The pump will start to pump the wa-
ter. When water will start to flow through the filter holder's
spout press the button again. Make sure the
ton is not pressed. Wait for the water to heat up and the
green indicator will light up. It means that the device
is ready to use.
Press button. Water will start to flow through the coffee
outlet. When the water flows for about 1 minute, press the
button again. Repeat the procedure a few times. Let
the device cool.
NOTE:
• B etween the operational cycles, the green indication
may turn off. This means that the heating process is
in progress. Wait for the device to be ready for use.
• During the first pumping of the water, there may be a
noise. This is normal, because the air is flowing from
the device. After about 20 seconds, the noise will stop.
ORDER OF OPERATION:
1. Open the tank's lid, Pic. D-2. Remove the water tank,
pulling it up, fill it with water to the MAX. You may also
add water without taking the tank out, Pic. D-1. Use
only clean, non-carbonated water at room temperature
25°C. Do not use any other liquids, such as hot water
or milk. This may lead to the coffee machine breakage.
14
1
2
5
, tray and tray grid
нbuttons are not pressed.
Do not turn on the device with empty water
tank. Make sure there is enough water in the
tank (above the MIN mark).
2. Plug in the device. Press
will light up.
NOTE:
The presence of water in the cavity under the tank is nor-
mal. Therefore, periodically drain it with a clean sponge.
The cup holder is heated up, when the device
is operating. Put coffee cups on it.
3. Place the ground coffee filter for 1 or 2 cups into the
filter holder. Make sure it is installed correctly, for this,
with a
turn it slightly to the right or left, so that the notches
on the filter fall into the grooves of the holder, pic. D-3.
4. Place the filter holder into the brew unit. For that, hold-
4
and
ing it with the handle to the left, bring it under the brew
unit, then insert it and turn the handle to the right, until
it locks. Pic. D-4.
5. To make espresso, it is necessary to warm up the de-
vice and filter holder. Press
start to pump the water. When water will start to flow
through the filter holder's spout press the
again. Wait for the water to heat up and the green indi-
cator will light up. Press
to flow through the coffee outlet. When the water flows
for about 20 seconds, press the
this only for the first portion of coffee.
6. After running the water, remove the filter holder by turn-
ing it to the left.
7. Using the measuring spoon, add 1-1.5 tablespoons of
ground coffee (~7 g) for one cup or 2 spoons of ground
coffee for two cups (~14 g) into the appropriate filter,
Pic. D-5. Use the other part of the measuring spoon to
press the coffee, Pic. D-6. Clean the edges of the filter
but-
holder from the remaining coffee.
The better you tamp the coffee, the darker it
will be, and vice versa.
8. Install the filter holder into the brew unit, Pic. D-4.
9. Take one or two preheated cups and place them under
the filter holder's spout, Pic. D-7.
10. Make sure the green indication
button is not pressed, and press
coffee. Coffee will start pouring into the cup from the
coffee outlet. When the required amount of coffee will
be poured, press
11. Remove the filter holder and clean it from coffee
grounds.
Clean the filter after every use.
NOTE:
• To remove the filter from the holder, you may use the
measuring spoon or any other filter, Pic. D-8.

PREPARING CAPPUCCINO

1. Take a big cup for cappuccino and prepare coffee ac-
cording to items 1-10.
2. Press the
button, the red indication
button. The pump will
button. Water will start
button again.
button and wait for the yellow indication
button
button again. Do
is lit, and
button to make