Water Filtering - Jacuzzi SKYLOUNGE Montageanweisung

value from a minimum of 15 °C to a maximum of 40 °C (59÷104 °F).
NOTE:
- Press and hold the button down until you reach the desired val-
ue; by releasing the button and pressing it again, the adjustment is
made in the opposite direction.
- During operation of the heater, the light spot on the screen next to
the temperature value flashes.
To show the temperature of the water in the tub again, do
not touch any key for about 5 seconds.
Models equipped with a Jacuzzi® CoolPower heat pump
- The heating is switched off (the filtration pump remains on for 30
seconds) as soon as the water temperature set-point is exceeded
(by about 1 °C), and is not switched on again until the temper-
ature does not drop by about 1.5 °C compared to the set-point.
To ensure precise measurement of the water temperature,
the filtering pump is turned on, approximately every half an
hour for 30 seconds (even if filtering cycles are not set).
When the system is turned off, or there is a power outage, the last
set point is stored in memory.
When heating is in operation, the LED located under the
bol comes on (if it flashes, this means that heating has been paused,
so as not to exceed the maximum permitted consumption; see the
information at the beginning of the chapter).
CAUTION
Do not use the hot tub if the water temperature is 40 °C
or more.
M
AINTENANCE OF MINIMUM TEMPERATURE OF WATER IN TUB
-
AND ANTI FREEZE PROTECTION OF THE PIPES
"Smart Winter" mode lets you make use of a special probe to
monitor the temperature of the compartment under the tub, which
contains the all of the pipes of the plumbing circuit. In extreme con-
ditions, the system may turn on this protection (indicated on the
display by the message ICE), switching on the pump(s).
ATTENTION: In the case of particularly low temperatures
specifically, check the electrical power supply regularly to
ensure that the function is not interrupted.
The pumps are turned on at pre-set intervals:
- temperature between 12 and 15 ° C (54 - 59 °F):
every 2 hours
- temperature between 9 and 12 ° C (48 - 54 °F):
every hour
- temperature between 6 and 9 ° C (42 - 48 °F):
every 30 minutes
- temperatures at or below 6 ° C (42 °F):
every 15 minutes
NOTES
- If the temperature of the compartment drops rapidly, the frequen-
cy of activation increases.
- If it becomes necessary to turn on the anti-freeze protection during
a filtering cycle, these will be suspended and resume when the cycle
is complete.
- If it is necessary to perform an anti-freeze cycle while a function
activated by the user is in progress, the cycle will be activated 15
minutes after the end of the function.
- If this protection is active, the spotlight may still be turned on.
When this function is on, the water heater only turns on again when
the temperature drops to approximately 10°C (50°F) below the set-
point.The minimum permitted temperature is 15°C.
perature is displayed.
down the "Light"
sym- the button is released the screen briefly shows the new refer-
ence value alternated with the word "Eco"; then, the current
temperature will appear again.
the "Up/Down"
NOTE:
- To check the function status, press the "Up/Down"
"Eco" appears, the function is on.
("S W ").
MART INTER

Water filtering

The water needs to be filtered to keep it clean and clear. This option
is active during the day as follows:
- two filtration cycles that are repeated every 12 hours.
Each filtration cycle is has an initial phase, in which the pump
is turned on one at a time for approximately one minute; then
the cycle continues, activating the Clearray™ Pro3tect™ and the
filtration pump for the remaining time.
To set the filtering cycle:
mately 5 seconds: dx (where "x" indicates the duration in hours)
appears on the screen.
(from a minimum of 0 to a maximum of 12 hours).
31
"E "
NERGY SAVINGS MODE
Press the "Up/Down"
While the LED above the thermometer symbol is on, hold
button for approximately 5 seconds: when
To turn the function off, proceed as indicated above (press
button, etc.).
S
ETTING THE FILTERING CYCLES
Hold down the "Pump"
Use the "Up/Down" button to enter the desired duration
(" " )
ECO FUNCTION
button (display B): the current tem-
button (display B) for approxi-
button: if