Using Your Cleaner; Cleaner Maintenance - Hoover XARION Handbuch

USING yOUR CLEANER

1. Extract power cord and plug it into the power supply. Do not pull the cord beyond
the red marker. [2]
2. Adjust the telescopic tube to the desired height by holding the handle and moving
the central hand grip up or down. [3]
3. Select carpet care control height by pressing the pedal in the nozzle.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
4. Switch the cleaner on by pressing the On/Off Button on the cleaner main body.
5. Adjust the suction by sliding the suction regulator to the desired level.
6. Switch off at the end of use by pressing the On/Off Button. Unplug and press the
cord rewind button to wind the power cord back into the cleaner. [7]
7. To store your cleaner adjust telescopic tube to the lowest height setting and park the
nozzle in the park position on the cleaner main body. [1]
ACCESSORIES
Please see the model specification on the packaging label for inclusion of accessories
to individual models. All accessories can be purchased separately from Hoover. (See
Hoover Spares and Consumable section).
All accessories can be fitted to the end of the hose or the end of the telescopic tube.
3 in 1 tool – Combines several functions in one, with maximum flexibility by the rotating
body. Reach into awkward areas by rotating the body. The 3 in 1 tool can be stored neatly
underneath the hose handle.
Crevice Tool – For corners and hard to reach areas.
Furniture Nozzle – For soft furniture and fabrics
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas. To ex-
tend the brushes push the button on the body of the tool.
Parquet Caresse Nozzle – For parquet floors and other delicate floors.
Allergen Remover Turbo Nozzle – Use the turbo nozzle for deep cleaning on carpets.
Allergen Remover Mini Turbo Nozzle – Use the mini turbo nozzle on stairs or for deep-
cleaning on textile surfaces and other hard to clean areas.
IMPORTANT: Do not use the turbo and mini turbo nozzles on rugs with long fringes,
animal hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while
the brush is rotating.
0565-5312 Xarion IM ML.indd 6
Downloaded from www.Manualslib.com
[4]
manuals search engine

CLEANER MAINTENANCE

Emptying the Dust Container
when the dust reaches the max level indicator in the container empty the dust container.
IMPORTANT:To maintain optimum performance do not allow the dust to sit higher than
the max level.
1. Release the container carry handle by lifting the centre latch to detach the dust
[5] container from the main cleaner and pull upward to remove. [8,9]
[6] 2. Hold the dust container over a bin with one hand and with the other pull the dust
container catch to open the door and empty. [10]
3. Close the dust container door and refit to the cleaner main body. To lock in place
push the container carry handle down until the latch connects with the main body
of the cleaner. Once correctly retained the carry handle will sits flush with the top
of the cleaner.
Cleaning the washable filters
The cleaner is fitted with a blue hepa filter pack. To maintain optimum cleaning perform-
ance regularly remove the the filters and tap against the side of the bin to release dust.
The filters should be washed every 3 months or when the filter has excessive dust level.
IMPORTANT: Regularly check and maintain the filters.
IMPORTANT: Always ensure the filter pack is fully dry before use.
To access the filter:
1. Unlock the filter door by pulling the filter latch upwards. Open the filter door.
2. Remove the filter pack by pressing down on the retainer catch to release. The filter
pack will pop up. Slide the filter pack out. [12,13]
3. Unlatch the filter pack frame.
4. Remove the foam micro filter from the pack.
5. Gently tap and wash the grey foam micro filter attached to the filter frame using
warm water. Do not use hot water or detergents. Remove excess water from the
filter and leave to dry fully before re-using. [14]
6. Gently tap and wash the Blue HEPA filter unit. Do not use hot water or detergents.
Remove excess water from the filter and leave to dry fully before re-using.
7. Reassemble to filter pack once fully dry and refit to the cleaner. Press on the top of
the filter to ensure it clips back into place. [15]
IMPORTANT: Do not use the product without the filter pack fitted.
NOTE: Ensure the carry handle is at its down position before opening the filter door.
6
GB
[11]
09/05/2008 12:15:25