Werbung
Verfügbare Sprachen
Verfügbare Sprachen
OPERATING INSTRUCTIONS
SPAS-2400/2+ USB CHARGER
ITEM NO.: 1219954
INTENDED USE
This product is designed to charge and power up to two suitable USB devices. Power is supplied via a
normal household mains socket. The product is protected against overload and short circuits.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be
avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use
can cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep
them. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
UP-TO-DATE OPERATING INSTRUCTIONS
Download the latest operating instructions at www.conrad.com/downloads or scan the
QR code shown. Follow the instructions on the website.
DELIVERY CONTENT
• USB charger
• Operating instructions
SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
b) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous
playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
‑ is visibly damaged,
‑ is no longer working properly,
‑ has been stored for extended periods in poor ambient conditions or
‑ has been subjected to any serious transport‑related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can
damage the product.
• Also observe the safety and operating instructions of any other devices which are connected
to the product.
• Never use the product immediately after it has been brought from a cold room into a warm
one. The condensation generated could destroy the product. There is also a risk of a fatal
electric shock! Allow the product to reach room temperature before connecting it to the power
supply and putting it to use. This may take several hours.
• Remove the product from the mains socket and the connected device when you are not using
it.
• The product generates heat during use. Ensure that there is sufficient ventilation and do not
cover the product during use.
• Do not short‑circuit the USB outputs.
• The mains socket that the device is plugged into must be easily accessible.
• Only connect the power adaptor to a normal mains socket connected to the public supply.
Before plugging in the power adaptor, check whether the voltage stated on the power adaptor
complies with the voltage of your electricity supplier.
• Never connect or disconnect power adaptors if your hands are wet.
• Never unplug the power adaptor from the mains socket by pulling on the cable; always use
the grips on the plug.
• When setting up the product, make sure that the cable is not pinched, kinked or damaged by
sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them. This poses
a risk of injury.
• For safety reasons, disconnect the power adaptor from the mains socket during storms.
• Never leave the product and the connected device unattended during use.
c) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you are not sure about the correct connection or use, or if questions arise which are not
covered by these operating instructions, please do not hesitate to contact our technical
support or another qualified specialist.
OPERATION
Always turn off the device that you want to connect before connecting it to the USB
connection.
Ensure that the product is connected properly. If it is not connected properly, it may
become hot or cause an electrical shock or fire. Ensure that your device is suitable for
the connection ratings of the product (see technical data).
You can charge or power two USB devices at the same time with the product. The steps for
connecting a single USB device are described below.
1. Turn off the USB device and connect it to the product with a suitable USB cable.
2. Insert the product into a normal household mains socket.
3. The USB device will now charge.
4. Unplug the product from the mains socket after use.
MAINTENANCE AND CLEANING
• Disconnect the product from the power supply.
• Do not immerse the product in water.
• Wipe the product regularly with a dry cloth.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines. You thus fulfill your statutory obligations and contribute to the protection of the
environment.
TECHNICAL DATA
Input voltage / current ............................................. 100 – 240 V/AC, 50/60 Hz, max. 550 mA
Output voltage / current .......................................... 5,0 V/DC, 2 x 2,4 A
Output power .......................................................... 2 x max. 12,0 W
Average active efficiency ........................................ 81.0 %
Efficiency at low load (10 %) .................................. 77.9 %
No load power consumption (W) ............................ 0.29 W
Protection class ...................................................... II
Operating conditions ............................................... 0 to + 35 °C, 25 ‑ 85 % RH (non‑condensing)
Storage conditions .................................................. ‑10 to +55 °C, 20 ‑ 90 % RH (non‑condensing)
Dimensions (W x H x D) ......................................... approx. 92 x 28 x 56 mm
Weight .................................................................... approx. 77 g
Commercial Registration Number:
HRB 3896
Manufacturer:
Conrad Electronic SE, Klaus‑Conrad‑Str. 1, D‑92240 Hirschau
This is a publication by Conrad Electronic SE, Klaus‑Conrad‑Str. 1, D‑92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
*1219954_v3_0220_02_dh_m_en
Werbung
