Herunterladen Diese Seite drucken

JTS TG-10R/1 Anleitung Seite 2

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

www.jts-germany.de
These instructions are intended for
ENGLISH
users without any specific technical
knowledge. Please read these instruc-
tions carefully prior to operation and
keep them and the attached fre-
quency list for later reference.
1 Applications
In combination with a receiver or several receivers of
the type TG-10R /1, the transmitter TG-10T/1 creates
a mobile wireless system for speech transmission, e. g.
for guided tours or multilingual lectures. For wire les s
transmission, 16 channels are available in the fre-
quency range of 863 – 865 MHz. Up to three of these
channels may be used at the same time without mutual
interference. The transmission range depends on local
conditions and may reach 60 m as a maximum.
1.1 Conformity and approval
Herewith, MONACOR INTERNATIONAL declare that the
transmitter TG-10T /1 and the receiver TG- 10R /1 com-
ply with the directive 2014 / 53 / EU. The EU declarations
of conformity are available on request from MONACOR
INTERNATIONAL. The wireless transmission system is
generally approved for operation in EU and EFTA coun-
tries; it is licence-free and requires no registration.
2 Important Notes
This unit corresponds to all relevant directives of the EU
and is therefore marked with
.
The unit is suitable for indoor use only. Protect it
against humidity and heat (admissible ambient tem-
perature range 0 – 40 °C).
For cleaning only use a dry, soft cloth; never use water
or chemicals.
No guarantee claims for the unit and no liability for
any resulting personal damage or material damage
will be accepted if the unit is used for other pur poses
than originally intended, if it is not correctly operated,
or if it is not repaired in an expert way.
If the unit is to be put out of operation de-
finitively, take it to a local recycling plant for
a disposal which will not be harmful to the
environment.
3 Power Supply
The transmitter / receiver is supplied with power via a
lithium-ion rechargeable battery: Prior to initial opera-
tion, fully recharge the battery. The following chargers
are available from JTS:
– charging station TG-10CH2 to recharge the batteries
of up to 2 units at the same time
– transport case TG-10CH18 to recharge the batteries
of up to 18 units at the same time
– transport case with castors TG-10CH36 to recharge
the batteries of up to 36 units at the same time
Do not put the unit in storage with a discharged battery.
If the unit is not used for a longer period, recharge the
battery every three months.
As the unit must be opened for replacing the battery,
a defective battery must always be replaced by skilled
personnel.
Defective rechargeable batteries must not be
placed in the household waste; always take
them to a special waste disposal.
Vertrieb von JTS-Produkten – Distrubution of JTS products
4 Connecting the Microphone to the Transmitter
When using the earband microphone instead of the
internal microphone (9), connect the earband micro-
phone to the jack MIC INPUT (1). Thus, the internal
microphone will be deactivated. If required, cover the
microphone cartridge with the pop shield provided.
Put the earband on your left ear so that the earlobe
support will press against your earlobe from the rear.
A clip is provided to attach the microphone cable to
your clothes.
5 Connecting the Earphone to the Receiver
As a padding for the earphone, wrap the foam cover
around it: Put the earphone with its printed side to the
rear into the unprinted pocket of the cover, wrap the
cover around the earphone and slip the second pocket
over it. The printing
sound is emitted. Connect the earphone to the jack
(1) and attach the earphone to your ear.
For transmitting the sound to a hearing aid, connect
the induction loop NL-90 (available as an accessory
from MONACOR) instead of the earphone. Put the loop
around your neck. Via a magnetic field, it will transmit
the sound to hearing aids with a "telephone coil".
6 Wearing the Unit
7 Operation
1) To switch on the units of the system, press the button
POWER (3). The POWER LED (4) will show green.
If it shows red, the battery is almost discharged and
should be recharged as soon as possible.
Whenever a button is pressed, the display (6) will
indicate the transmission channel adjusted for approx.
9 seconds, then the channel number will disappear.
To reactivate the display for approx. 9 seconds, shortly
press a button on the unit.
2) Select a transmission channel from the channels
to
available. Always set the transmitter and the
receiver / receivers of a system to the same channel.
To set the channel, keep the button CHANNEL
(7) pressed until a dot starts flashing on the display
next to the channel number. Then press the button
CHANNEL repeatedly until the desired channel is
indicated. When the dot on the display disappears
approx. 6 seconds after the last actuation of the
button CHANNEL, the channel selected has been
memorized.
3) Speak into the internal microphone (9) of the trans-
mitter or into the earband microphone connected.
With the control (8), adjust the volume of the audio
signal transmitted on the transmitter and the repro-
duction volume on the receiver. Caution: Never
adjust a very high volume. Permanent high volumes
may damage your hearing!
®
MONACOR INTERNATIONAL GmbH & Co. KG, Zum Falsch 36, 28307 Bremen, Germany
Copyright
©
by MONACOR INTERNATIONAL. All rights reserved.
will mark the side where the
To wear the transmitter / receiver,
attach the clip (5) to your clothes
(e. g. belt or trouser pocket) or use
the neckband: Pull the loop of the
band over the clip, slide the push-
button to the desired length of the
band and put the band around your
neck. By unlocking the snap connec-
tion (
figure on the left), the unit
is easily removed and exchanged
against another one.
TG-10R /1
Order number 25.3070
TG-10T/1
Order number 25.3080
Tour Guide System 863 – 865 MHz
4) If the reception is poor or disturbed, check
– if the reception can be improved by using a different
transmission channel.
– if the transmitter and the receiver are too far apart.
– if there are obstacles in the transmission path which
may shield the radio signal.
Up to three systems TG-10./1 transmitting on dif-
ferent channels may be operated in parallel without
interference. When several systems are operated
in parallel, make sure to keep a sufficient distance
between the individual systems.
5) To reset a unit in case of malfunction, press the button
RESET (2) by means of a thin object, e. g. a metal
pin. The unit will be switched off and may be set into
operation again.
6) To switch off the units, keep the button POWER
pressed until the POWER LED is extinguished.
8 Specifications
Radio frequency range: � � � � 863 – 865 MHz (channel assignment
 frequency list attached)
Audio frequency range: � � � 40 Hz–18 kHz
Transmitting power: � � � � � � < 10 mW
Internal microphone
of transmitter: � � � � � � � � � � � electret microphone (cardioid)
Accessories
Transmitter: � � � � � � � � � � � electret earband microphone
(omnidirectional) with cable clip and
2 × pop shield, neckband
Receiver: � � � � � � � � � � � � � dynamic mono earphone with
padding, neckband
Power supply: � � � � � � � � � � � lithium-ion battery 3�7 V/ 1300 mAh
Operating time of battery: � up to 14 hours
(depending on volume)
Dimensions, weight: � � � � � � 54 × 99 × 17 mm, 80 g
Subject to technical modification.
1
2
3
4
RESET
POWER
5
6 7
8
5
TG-10R /1
A-1227.99.03.11.2016
1
2
3
4
RESET
MIC INPUT
POWER
6 7
8
TG-10T/1
9

Werbung

loading

Diese Anleitung auch für:

Tg-10t/1