JVC DLA-G150CLE Bedienungsanleitung Seite 44

Menu Operations
I
Quick Reference Guide for PC Menu Mode
Main Menu in PC Menu Mode (While receiving computer-related signals)
Image adj. → (Refer to page 49)
Contrast:
Brightness:
Sharpness:
All reset:
Set up
Tracking:
Phase:
Position:
Resize:
Clamp:
Color temp.
Color temp.:
RED:
GREEN:
BLUE:
All-reset:
Options → (Refer to page 54)
Options 1
Menu display:
Line display:
Lamp time display:
Keystone:
Lamp control:
Page 2:
Language
Japanese / English* / German / Spanish / Italian / French
Information → (Refer to page 56)
Input:
Switcher:
Resolution:
Frequency H:
Frequency V:
Lamp time:
* : Factory set value.
42
Contrast of the picture image being projected can be adjusted. (–30 to +30, 0*)
Brightness of the picture image being projected can be adjusted. (–30 to +30, 0*)
Adjust the outline of letters etc. (1 / 2 / 3 / 4 / 5, 3*)
Resets above items to the factory set values.
Yes / No
The lateral size and display area of picture image can be adjusted. (–128 to +127)
→ (Refer to page 47)
Flickering or dim picture image can be adjusted. (0 to 31) → (Refer to page 47)
Video screen position and menu position can be adjusted. → (Refer to page 51)
Disp. Posi. / Menu
The relationship between the number of pixels (resolution) and the screen can be
selected. → (Refer to page 53)
"1:1":
Panel:
Aspect*:
Selectable clamp position. Normally, set to "BP". ST / BP*
Adjustable color temperature, Low/Middle* /High.
Will be adjusted to correct reddish or blueish image.
Adjusts the red level. (o to 255, the adjustable range varies depending on signals)
Adjusts the green level. (o to 255, the adjustable range varies depending on signals)
Adjusts the blue level. (o to 255, the adjustable range varies depending on signals)
Reset above items to the factory set values.
Yes/No
15sec* (Menu disappears in 15 seconds.) / ON (Menu stays on.)
5sec* (Line display such as "PC1" or "PC2" appears on top right of the screen for 5
seconds when the VIDEO or PC button is pressed.) / OFF (Line display does not
appear.)
ON*: Displays when the lamp use time reaches 1000 hours when set in the LPC or LOC mode.
Does not display when the lamp use time reaches 1000 hours when set in the LPC or LOC
OFF:
mode.
Press ENTER to enter the Keystone submenu.
Keystone:
Normal*: Used as a normal lamp.
LPC: Lamp brightness is aLutomatically controlled with time.
LOC: Lamp brightness is controlled in 7 levels (-6 to 0) irrespective of the time. This is set within
the menu.
Press ENTER to enter the "Page 2" submenu.
Flip H:
Flip V:
RS-232C [bps]:
Sleep time [min]:
Page 1:
Language for on-screen display. → (Refer to page 46)
Shows the terminal name selected by the PC button. (PC1 or PC2)
This display currently has no meaning. ("CH.0" is usually displayed to indicate that it is not being used.)
Shows the resolution of the input signal being received. (Horizontal × Vertical)
It may not be displayed correctly with some input signals.
Shows the horizontal frequency of the input signal being received. (
Shows the vertical frequency of the input signal being received. (
Accumulated used hours of the light-source lamp.
Picture image is projected with its original size.
Picture image is enlarged to the full size.
Picture image is enlarged while maintaining the original aspect ratio.
Adjust to correct the trapezoidal distortion of the projected image.
(–80 to +128, 0*)
OFF* / ON (Select for upside-down hanging on the ceiling.)
OFF* / ON (Select for upside-down hanging on the ceiling.)
Selectable baud rate (transmission speed). 9600 / 19200*
Selectable sleep times. If no-signal condition continues for the
period of selected time (Unite: Minutes), the projector enters the
stand-by mode. 15 / 30 / 60 / OFF*
Press ENTER to return to the "Page 1" submenu.
kHz)
Hz)