Operation - EINHELL TE-OS 18/230 Li Originalbetriebsanleitung

ding/grinding paper coincide with the oscilla-
ting plate.
5.4 Fastening the sanding/grinding paper
with the Velcro fastening system (Fig. 7)
•
Only use sanding/grinding paper with the
corresponding dimensions and matching per-
forations.
•
Place the sanding/grinding paper onto the
oscillating plate (5) as shown in figure 7.

6. Operation

6.1 Charging the LI battery pack (Fig. 8/9)
1. Remove the battery pack (a) from the handle,
pressing the pushlock buttons (b) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(c) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 "Charger indicator" you will fi nd a
table with an explanation of the LED indicator on
the charger.
Store the rechargeable battery, cordless tool and
charger in a dry place with an ambient tempera-
ture of: Rechargeable battery = 10-20°C
Cordless tool, charger = 10-40°C.
If the battery pack fails to become charged, ple-
ase check
•
whether there is voltage at the socket-outlet
•
whether there is proper contact at the char-
ging contacts on the charger.
If the battery still fails to become charged, please
return
•
the charger
•
the battery pack
to our Customer Service Department.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
Anl_TE-OS_18_230_Li_Solo_SPK9.indb 19 Anl_TE-OS_18_230_Li_Solo_SPK9.indb 19
GB
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6.2 Battery capacity indicator
(Fig. 10 – Item e)
Press the battery capacity indicator switch (d).
The battery capacity indicator (e) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.
6.3 Switching the equipment ON/OFF
(Fig. 11)
To switch on:
Push the ON/OFF switch (1) forwards.
To switch off :
Push back the ON/OFF switch into its starting
position.
6.4 Speed control (Fig. 12/Item 6)
To pre-select the speed turn the knurled screw (6)
on the switch.
Plus direction:
Minus direction:
6.5 Working with the orbital grinder/sander
•
Place the whole surface area of the sanding
disk on the material.
•
Switch on the machine and move it with gent-
le pressure over the workpiece completely
circular movements or moving it to and fro
and up and down.
•
Use a coarse paper for coarse sanding and a
finer paper for finish sanding. You can find the
- 19 -
Higher speed
Lower speed
13.08.2020 07:18:05 13.08.2020 07:18:05