Using A Microphone; Clock And Timers; Setting The Clock; Sleep Timer - Panasonic SA-MAX4000 Bedienungsanleitung

MAX4000E.book Page 15 Tuesday, April 21, 2015 4:57 PM

Using a microphone

Preparation
Decrease the volume of the system to its minimum before
you connect or disconnect a microphone.
1
Connect a microphone (not supplied) to the
microphone jack.
Plug type: Ø 6.3 mm monaural
2
Turn [MIC VOL, MIN/MAX] on the main unit to
adjust the volume of the microphone.
If you want to sing with the background music.
3
Play the music source and adjust the volume of
the system.
Note:
•
If a strange noise (howling) is emitted, move the
microphone away from the speakers, or decrease the
volume of the microphone.
•
When you do not use the microphone, disconnect it from
the microphone jack, and decrease the volume of the
microphone level to "MIN".
• This system cannot record from microphone.

Clock and timers

Setting the clock

This is a 24-hour clock.
1
Press [SETUP] to select "CLOCK".
2
Press [Y, U] to set the time and then press [OK].
To check the time
Press [SETUP] to select "CLOCK".
In standby mode, press [DISPLAY].
Note:
Reset the clock regularly to maintain accuracy.
Play timer and record timer
®
(Except for Bluetooth , AUX 1 and AUX 2 source)
You can set the timer to come on at a certain time to:
• Wake you up (play timer).
• Record from the radio (record timer).
Play timer and record timer cannot be used together.
Preparation
Set the clock.
1
Press [SETUP] to select "TIMER ADJ".
2
Press [Y, U] to select "#PLAY" or "#REC" and
then press [OK].
3
Press [Y, U] to set the start time and then press
[OK].
4
Do step 3 again to set the end time.
offset printing
5
Press [Y, U] to select the source you want to play
or record and then press [OK].
6
For record timer, press [Y, U] to select "MEMORY"
or "USB B" to keep the recording and then press
[OK].
To start the timer
1
Prepare the source.
Play timer Prepare the source you want to
listen to (disc, USB, internal
memory or radio) and set the
volume.
Record timer Connect the USB device to
(for USB recording) and tune in to
the radio station.
2
Press [SETUP] to select "TIMER SET".
3
Press [Y, U] to select the setting and then press
[OK].
PLAY ON Start the play timer.
PLAY OFF Cancel the play timer.
REC ON Start the record timer.
REC OFF Cancel the record timer.
"#" is shown.
The system must be switched off for the timer to
operate.
To check the setting
1
Press [SETUP] to select "TIMER ADJ".
2
Press [Y, U] to select "#PLAY" or "#REC" and
then press [OK].
In standby mode, press [DISPLAY] two times.
Note:
• The play timer starts at a low volume and increases
gradually to the preset level.
•
The record timer starts 30 seconds before the set time with
the volume muted.
•
The timer comes on at the set time every day if the timer is
on.
•
If you switch off the system and then switch on again while
a timer is in operation, the timer will not stop at the end
time.

Sleep timer

The sleep timer switches off the system after the set time.
Press [SLEEP] to select the setting (in minutes).
To cancel, select "OFF".
3 0 M N I 60 MIN 90 MIN
Note:
•
The remaining time is always shown on the display. The
display changes temporarily when you perform other
operations.
• The play timer and sleep timer or the record timer and sleep
timer can be used together.
• The sleep timer always comes first. Be sure not to set an
overlap of timers.
USB B
120 MIN O F F
15
15