Safety Information; Operation - Cloer 5918 Bedienungsanleitung

Description of appliance / parts:
1. Coffee pot with lid
2. Filter insert
3. Water tank with safety valve
4. Contact base with cord
Preparation for use
·
Remove all packaging elements and labels, but
not the rating plate.
·
Place the espresso maker on a dry, level, and
non-slip surface.
·
Make sure that the power cord never comes into
contact with hot surfaces.
·
Do not stretch the cord over corners and edges.
Before initial use
·
Clean the coffee pot, the filter insert, and the
water tank under clear, warm water to remove
any possible production residue.
·
Make sure not to immerse the contact base or
the water tank in water.
·
For hygienic reasons, we recommend that you
prepare and pour away a cup of espresso before
making your first real cup of espresso. You can
brew this trial espresso with the amount of
coffee required to make 3 cups.

Safety information

The appliance meets the
requirements of the applicable
EC directives.
The appliance is intended
for in door use only.
·
Use the espresso maker only with the provided
contact base.
·
Do not place the contact base and the coffee
pot on a stove or gas flame.
·
The contact base may only be operated when
it is dry.
·
Please make sure that water is never spilled on
the contact base.
·
If water is accidentally spilled onto the contact
base, proceed as follows:
– Unplug the unit from the wall socket.
– Dry the contact base with an absorbent dry
kitchen towel.
– Dry the surface beneath the contact base.
– Plug the unit into the wall socket again.
CAUTION!
The espresso maker becomes
hot during operation. There is
a hazard of burn injury!
Avoid touching the surface of the
appliance. Grab the espresso
maker only by its insulated
handle!
·
Do not open the lid of the coffee pot during
operation. Scalding may result from escaping
steam!
·
Wait until the boiling process is complete and
the control lamp turns off.
Do not remove the espresso
maker from the contact base
during brewing! Never try to
remove or re-adjust the coffee pot
and the water tank or perform
similar operations during the
operation of the espresso maker!
·
Unplug the power cord immediately if the
appliance, the rubber gasket or the electric cord
has become damaged.
·
Unplug the appliance after using it.
·
Use only espresso coffee powder.
CAUTION!
Fill the water tank only with
water and never with milk, sugar
or other liquids or ingredients!
·
Do not overfill the espresso maker. If the
espresso maker is overfilled, boilling coffee may
be ejected.
ATTENTION!
Always unplug appliance when
not in use and before cleaning!

Operation

·
Fill water into the water tank up to the mark „4".
·
For a stronger espresso fill the water only up to
mark „3".
·
Take the filter insert and fill it loosely with
ground espresso powder.
·
Smooth the espresso powder lightly over the
edge, but do not press the espresso powder
into the filter.
·
Insert the filled filter insert into the water tank.
·
Remove any powder residues from the edge so
that the seal can close perfectly.
·
Screw the top of the espresso maker onto
the water container by placing the top of
the espresso maker straight onto the water
container and turning clockwise until the two
arrows are aligned.
·
Ensure that the containers are not tilted and
that the pot is really tight, so that steam cannot
escape.
·
Now place the espresso pot on the contact
socket.
·
Plug the plug into the socket.
·
Switch the espresso maker on.
·
Do not open the lid during the brewing process.
·
Risk of scalding!
·
The espresso is ready when the control lamp
goes out
·
Pull the power plug out.
·
Now you can serve the espresso.
CAUTION!
The housing of the espresso
maker is hot! Grab the pot only
by its handle!
·
Before making more espresso, let the appliance
cool off first.
·
After that please clean the espresso maker
according to clause cleaning.
·
Then, proceed as described above.
EN
9