+050004175 - rel. 1.1 - 06.03.12
PJS5 easy
- ENERGY SAVING con micro porta/ ENERGY SAVING with door switch
Dimensioni (mm) / Dimensions (mm)
74
81
71x29
Montaggio a pannello / Panel mounting
Frontale (con 2 viti ø 2,5x12 mm) / Front (with 2 screws ø 2,5x12 mm)
1
tipo Pozidriv
Pozidriv type
non eccedere
nel serraggio
max 2,5
do not tighten
excessively
Da dietro (con 2 staffe posteriori) / Rear (with 2 quick-fi t side brackets)
2
1
Collegamenti elettrici / Electrical connections
115 Vac
230 Vac
serial conv.
IROPZ485S0
prog. key
IROPZKEY* or PSOPZKEY*
Tabella allarmi
Codice allarme buzzer e relè allarme LED Descrizione allarme
E0
attivi
ON
errore sonda 1= regolazione
E1
non attivi
ON
errore sonda 2= defrost
E3
attivi
ON
Allarme perdita di refrigerante
dOr
attivi
ON
allarme porta aperta
LO
attivi
ON
allarme bassa temperatura
HI
attivi
ON
allarme alta temperatura
EE
non attivi
ON
errore parametri macchina
EF
non attivi
ON
errore parametri funzionamento -
dF
non attivi
OFF defrost in esecuzione
ECO
non attivi
OFF risparmio energetico attivo
Table of alarms
Alarm code
buzzer and alarm relay LED
Description
E0
active
ON
probe 1 error= control
E1
inactive
ON
probe 2 error= defrost
E3
active
ON
refrigerant system failure alarm
dOr
active
ON
open door alarm
LO
active
ON
low temperature alarm
HI
active
ON
high temperature alarm
EE
inactive
ON
unit parameter error
EF
inactive
ON
operating parameter error
dF
inactive
OFF
defrost running
ECO
inactive
OFF
energy saving active
IMPORTANT WARNINGS
The CAREL product is a state-of-the-art product, whose operation is specifi ed in the technical docu-
mentation supplied with the product or can be downloaded, even prior to purchase, from the website
www.carel.com. - The client (builder, developer or installer of the fi nal equipment) assumes every
responsibility and risk relating to the phase of confi guration the product in order to reach the expected
results in relation to the specifi c fi nal installation and/or equipment. The lack of such phase of study,
which is requested/indicated in the user manual, can cause the fi nal product to malfunction of which
CAREL can not be held responsible. The fi nal client must use the product only in the manner described
in the documentation related to the product itself. The liability of CAREL in relation to its own product
is regulated by CAREL's general contract conditions edited on the website www.carel.com and/or by
specifi c agreements with clients.
WARNING: separate as much as possible the probe and digital input signal
NO POWER
& SIGNAL
CABLES
cables from the cables carrying inductive loads and power cables to avoid possible
TOGETHER
READ CAREFULLY IN THE TEXT!
electromagnetic disturbance. Never run power cables (including the electrical panel
wiring) and signal cables in the same conduits.
Smaltimento del prodotto: L'apparecchiatura (o il prodotto) deve essere oggetto di
raccolta separata in conformità alle vigenti normative locali in materia di smaltimento
Disposal of the product: the appliance (or the product) must be disposed of separa-
tely in accordance with the local waste disposal legislation in force.
Descrizione
PJS5 rappresenta una gamma di regolatori elettronici a microprocessore con visualizzazione a LED realizzati
NO POWER
per la gestione del risparmio energetico delle unità frigorifere, tramite la rilevazione del micro porta. Lo stato
& SIGNAL
CABLES
TOGETHER
della porta determina il cambiamento del set point e l'accensione/spegnimento della luce.
READ CAREFULLY IN THE TEXT!
Caratteristiche tecniche
alimentazione
230 Vac +10 /-15% 50/60 Hz; 115 Vac +10 /-15% 50/60 Hz
12 Vac +10/-15% 50/60 Hz classe 2; 12 Vdc +10/-20% classe 2
potenza nominale 3,5 VA
ingressi
sonda NTC o PTC 1 o 3 ingressi.
Ingresso digitale in alternativa a terza sonda
uscite relè
relè 2 Hp UL: 12 A Res. 10 FLA 60 LRA - 240 Vac
relè 16 A UL: 12 A Res. 5 FLA 30 LRA - 240 Vac C300,
relè 8 A UL: 8 A Res. 2 FLA 12 LRA - 240 Vac C300,
10
58
NTC Std CAREL 10 Ka 25 °C, PTC Std CAREL 985 a 25 °C
tipo di sonda
65,29
3
connessioni
morsetti fi ssi a vite per cavi con sez. da 0,5 mm
blocchetti a vite o con contatto a crimpare (sez. cavo fi no a 2,5 mm
nominale massima per morsetto 12 A.
montaggio
per terminale: mediante viti dal frontale o con staffe posteriori
visualizzazione
display LED 3 cifre con segno (-199...999) e punto decimale; sei LED di stato
Fig. 1
condizioni di funzionamento
condizioni di immagazzinamento
intervallo di rilevazione
grado di protezione frontale
contenitore
classifi cazione secondo la protezio-
ne contro le scosse elettriche
2
3
inquinamento ambientale
PTI dei materiali di isolamento
periodo delle sollecitazioni elettri-
che delle parti isolanti
categoria di resistenza al calore e
al fuoco
immunità contro le sovratensioni
tipo di azione e disconnessione
n.ro di cicli di manovra delle opera-
zioni automatiche relè
classe e struttura del software
Fig. 2
pulizia dello strumento
lunghezza max. cavi
AVVERTENZA: non passare cavi di potenza a meno di 3 cm dalla parte inferiore del dispositivo o dalle sonde; per le
connessioni usare solo cavi di rame.
Tabella parametri
Parametro
PS Password
Fig. 3
/
PARAMETRI SONDA
/2 Stabilità misura sonde
/4
Selezione sonda visualizzata
/5 Selezione u.d.m. sonde °C / °F
/6 Disabilita punto decimale
/8 Offset di visualizzazione
/9 Temperatura minima visualizzata
/A Temperatura massima visualizzata
/b Soglia di segnalazione temperatura visualizzata
/E
Stabilità temperatura visualizzata
/C1 Offset sonda 1
/C2 Offset sonda 2
r
PARAMETRI REGOLAZIONE
St
Set point
rd Differenziale
r1
Set point minimo ammesso
r2
Set point massimo ammesso
r4
Aumento del Set-Point durante il Risparmio Energetico
r5
Differenziale durante il Risparmio Energetico
r6
Tempo commutazione automatica da Normale a Risparmio
Energetico
r6 = 0 è suggerito per i cabinet aperti, il Risparmio Energetico è
Fig. 4
attivato immediatamente alla chiusura della tenda
r7
Tempo commutazione automatica da Risparmio Energetico
a Normale
r8
Per attivazione manuale da tastiera del Risparmio Energetico:
nei casi di termostato installato internamente al cabinet,
rappresenta il tempo di attesa di chiusura della porta.
r9
Tempo che il modo Risparmio Energetico resta disabilitato dopo
il raggiungimento del Set Point per la prima volta dall'accen-
sione del cabinet
Pt
Differenziale per il pull-down
Parametri
C
PARAMETRI COMPRESSORE
coinvolti
c0 Ritardo Start Comp.
-
c1 Tempo minimo tra accensioni successive
[d0 = 0 / 1]
c2 Tempo minimo di Off del compressore
d12
c3 Tempo minimo di On del compressore
[A4 = 7/8][+A7]
c4 Duty setting
[AL] [Ad]
d
PARAMETRI SBRINAMENTO
[AH] [Ad]
d0 Tipo di sbrinamento
-
INIZIO
0
A tempo (dI)
[d6=0]
1
A tempo (dI)
-
2
In temperatura (d10)
3
In temperatura (d10)
d01 Defi nisce se sbrinamento a gas caldo o meno.
0 = sbrinamento normale ( compressore OFF )
Parameters
1 = sbrinamento gas caldo ( compressore ON )
involved
dI
Intervallo tra i defrost
1dI Modalità di conteggio dell'intervallo dI:
-
[d0 = 0 / 1]
0 = dI viene conteggiato sempre;
1 = dI viene conteggiato solo quando il compressore è ON
d12
dt
Temperatura Evaporatore di fi ne defrost
[A4 = 7/8][+A7]
dP Durata massima defrost ALARM_ED
[AL] [Ad]
d4 Abilitazione defrost allo start up
[AH] [Ad]
d5 Ritardo defrost da start up o da IngDi
-
d6 Blocco display durante il defrost
-
dd Tempo di gocciolamento dopo il defrost
[d6=0]
d8 Esclusione allarmi dopo il defrost
-
d9 Priorità defrost su protezioni compressore
d/ Valore sonda defrost
d10 Temperatura sonda Evaporatore per inizio defrost
d11 Temperatura sonda Regolazione per abiliazione defrost
d12 Allarme Perdita Refrigerante: tempo di monitoraggio della
tendenza a scendere della temperatura di regolazione
A
PARAMETRI DI ALLARME
A0 Differenziale allarmi e ventole
AL Soglia/Scostamento di allarme di bassa temperatura
AH Soglia/Scostamento di allarme di alta temperatura
Ad Ritardo allarme bassa e alta temperatura
A10 Ritardo allarme porta aperta
F
PARAMETRI VENTOLE EVAPORATORE
F0 Ritardo Start Ventole
Fd0 Ciclo del ventilatore a compressore spento: tempo di ON
FdF Ciclo del ventilatore a compressore spento: tempo di OFF
Fn0 Ciclo del ventilatore a compressore spento durante il
Risparmio Energetico: tempo di ON
FnF Ciclo del ventilatore a compressore spento durante il
Risparmio Energetico: tempo di OFF
H
ALTRE IMPOSTAZIONI
H0 Indirizzo seriale
H4 Disabilitazione buzzer
0= buzzer abilitato; 1= buzzer disabilitato
H5 Rileva parametri modifi cati
EN60730-1: 10(10) A 250 Vac
EN60730-1: 12(2) A NO/NC, 10(4) A fi no 60 °C NO, 2(2) A CO - 250 Vac
EN60730-1: 8(4) A NO, 6(4) A NC, 2(2) A CO - 250 Vac
2
a 1,5 mm
2
. Morsetti estraibili per
2
). Corrente
-10T50 °C - umidità <90% U.R. non condensante
-20T70 °C - umidità <90% U.R. non condensante
-50T90 °C (-58T194 °F) - risoluzione 0,1 °C/°F
montaggio a quadro con guarnizione: IP65 tipo 1
terminale plastico, 81x36x65 mm
Classe II per incorporamento adeguato
normale
250 V
lungo
categoria D (UL94 - V0)
categoria 1
contatti relè 1C
EN60730-1: 100.000 operazioni
UL:
30.000 operazioni (250 Vac)
Classe A
utilizzare esclusivamente detergenti neutri ed acqua.
seriale: 1 km
sonde: 30 m
relè: 10 m
Min.
Max.
Def.
0
200
22
1
15
4
1
3
1
0
1
0
0
1
0
-99.0
+99.0
0.0
-40.0
/A
-3.5
/9
/b
3.0
/A
199.0
13.0
1
50
10
-12,7
12,7
0,0
-12,7
12,7
0,0
r1
r2
4,0
0,0
19,0
2,0
-50,0
r2
-50,0
r1
150,0
90,0
1,0
50,0
3,0
0,0
19,0
4,0
0
90
4
1
90
6
0
90
10
0
24
hour
-50
127
30
1
100
6
0
100
0
0
100
0
0
100
0
0
100
0
0
3
-
FINE
A tempo (dP)
In temperatura (dt)
In temperatura (dt)
A tempo (dP) con controllo in
temperature (dt)
0
1
-
0
199
8
0
1
-
-50,0
127,0
4,0
1
199
30
0
1
0
0
199
0
0
1
0
0
15
0
0
15
0
0
1
0
0
0
0
-50,0
127,0
-10,0
-50,0
127,0
15,0
A10
200
60
-20,0
20,0
2,0
-50,0
150,0
0,0
-50,0
150,0
0,0
0
199
0
0
10
5
1
100
3
1
100
5
1
100
10
1
100
5
1
100
20
0
207
1
0
1
0
1
199
0
Description
PJS5 represent a range of electronic microprocessor controllers with LED display developed for the
management of the energy saving display cabinets and showcases, by the detection of door-switch.
The status of the door determines the change of set point and ON/OFF of the light.
Technical specifi cations
power supply 230 Vac +10 /-15% 50/60 Hz; 115 Vac +10 /-15% 50/60 Hz
12 Vac +10/-15% 50/60 Hz class 2; 12 Vdc +10/-20% class 2;
rated power
3,5 VA
inputs
NTC or PTC probes 1 or 3 inputs.
Digital input as alternative to third probe
relay outputs
2 HP relay UL: 12 A Res. 10 FLA 60 LRA - 240 Vac
EN60730-1: 10(10) A 250 Vac
16 A relay UL: 12 A Res. 5 FLA 30 LRA - 240 Vac C300,
EN60730-1: 12(2) A NO/NC, 10(4) A up to 60 °C NO, 2(2) A CO - 250 Vac
8 A relay
UL: 8 A Res. 2 FLA 12 LRA - 240 Vac C300,
EN60730-1: 8(4) A NO, 6(4) A NC, 2(2) A CO - 250 Vac
type of probe Std CAREL NTC 10 Kat 25 °C, Std CAREL PTC 985 at 25 °C
connections
screw terminals for cables with cross-sect. from 0.5 mm
for screw blocks or with crimped contact (cable cross-sect. up to 2.5 mm
maximum current per terminal 12 A.
assembly
terminal: using screws from the front panel or with rear brackets
display
3 digit LED display with sign (-199 to 999) and decimal point; six status LEDs
operating conditions
-10T50 °C - humidity <90% rH non-condensing
storage conditions
-20T70 °C - humidity <90% rH non-condensing
range of measurement
-50T90 °C (-58T194 °F) - resolution 0.1 °C/°F
front panel index of protection
panel installation with IP65 type 1 gasket
case
plastic terminal, 81x36x65 mm
classifi cation according to protec-
Class II when suitably integrated
tion against electric shock
environmental pollution
normal
PTI of the insulating material
250 V
period of stress across the insu-
long
lating parts
category of resistance to heat
category D (UL94 - V0)
and fi re
immunity against voltage surges category 1
type of action and disconnection 1C relay contacts
no. of relay automatic operating
EN60730-1: 100,000 operations
cycles (*)
UL:
30,000 operations (250 Vac)
software class and structure
Class A
cleaning the instrument
Only use neutral detergents and water.
cable max. lenght
serial: 1 km
probes: 30 m
relay: 10 m
WARNING: do not run the power cable less than 3 cm from the bottom part of the device or from the probes; for the
connections only use copper wires.
Table of parameters
U.M.
Parameter
PS
Password
/
PROBE PARAMETERS
/2
Measurement stability
/4
Select probe/input displayed
/5
Select °C / °F
/6
Disable decimal point
°C/°F
/8
Visualization offset
°C/°F
/9
Minimum shown temperature
°C/°F
/A
Maximum shown temperature
°C/°F
/b
Signaling temperature threshold
Min.
/E
Shown temperature stability
°C/°F
/C1 Probe 1 offset
°C/°F
/C2 Probe 2 offset
r
CONTROL PARAMETERS
°C/°F
St
Set point
°C/°F
rd
Standard differential
°C/°F
r1
Minimum set point allowed to the user
°C/°F
r2
Maximum set point allowed to the user
°C/°F
r4
Increase the Set-Point during Energy Saving
°C/°F
r5
Differential during Energy Saving
hr
r6
Automatic time from Normal to Energy Saving
If r6 = 0 Saving Mode is restored immediately when the
door is closed, this setting is indicated for "Open Front" cabi-
net with curtain instead of door.
hr
r7
Automatic time from Energy Saving to Normal
r8
To enter in Saving mode by keyboard:
sec
time to allow the door closure for "Open Front" cabinet.
r9
Time that Energy Saving mode remains disabled after
reaching the set point the fi rst time when the cabinet is
4
switched on
Pt
Pull-down differential
C
COMPRESSOR PARAMETERS
°C/°F
c0
Fan start delay
c1
Min. time between successive comp. starts
c2
Min. compressor OFF time
sec
min
c3
Min. compressor ON time
min
c4
Duty setting
min
d
DEFROST PARAMETERS
min
d0
Type of defrost
START
STOP
0
0
By time (dI)
By time (dP)
1
By time (dI)
By temperature (dt)
2
By temperature (d10) By temperature (dt)
3
By temperature (d10) By time (dP) with temperature
control (dt)
d01 Defi nes whether or not defrost is hot gas.
0 = normal defrost (compressor OFF)
0
1 = hot gas defrost (compressor ON)
dI
Interval between two defrosts
1dI Mode for counting the interval dI:
hr
0 = dI is always counted;
0
1 = dI is only counted when the compressor is ON
dt
End defrost temperature
dP
Max. or effective defrost duration ALARM_ED
°C/°F
d4
Defrost when the instrument is switched on
d5
Defrost delay on start-up or from digital input
min
d6
Disable temperature display during defrost
min
dd
Dripping time after defrost
d8
Alarm bypass time after defrost
min
d9
Defrost priority over compressors protectors
hr
d/
Display defrost probe temp.
d10 Start up defrost evaporator temperature
d11 Regulation temperature enable defrost
°C/°F
d12 Refrigerant system failure alarm: monitoring time to
°C/°F
°C/°F
decrease the regulation temperature
min
A
ALARM PARAMETERS
A0
Alarm and fan differential
AL
Low temperature alarm threshold/deviation a
AH High temperature alarm threshold/deviation
°C/°F
Ad
Low and high temperature alarm delay
°C/°F
A10 Open door alarm delay
°C/°F
min
F
FAN PARAMETERS
min
F0
Start Fan delay
Fd0 Fan duty cycle compressor OFF: ON time
FdF Fan duty cycle compressor OFF: OFF time
sec
Fn0 Fan duty cycle compressor OFF during energy saving:
min
ON time
min
min
FnF Fan duty cycle compressor OFF during energy saving:
OFF time
min
H
OTHER SETTINGS
H0
Serial address
H4
Disable buzzer
0= buzzer enabled; 1= buzzer disabled
H5
Modifi ed parameters detect
2
to 1.5 mm
2
. Plug-in terminals
2
). Rated
Min.
Max.
Def.
U.M.
0
200
22
1
15
4
1
3
1
0
1
0
0
1
0
-99.0
+99.0
0.0
°C/°F
-40.0
/A
-3.5
°C/°F
/9
/b
3.0
°C/°F
/A
199.0
13.0
°C/°F
1
50
10
Min.
-12,7
12,7
0,0
°C/°F
-12,7
12,7
0,0
°C/°F
r1
r2
4,0
°C/°F
0,0
19,0
2,0
°C/°F
-50,0
r2
-50,0
°C/°F
r1
150,0
90,0
°C/°F
1,0
50,0
3,0
°C/°F
0,0
19,0
4,0
°C/°F
0
90
4
hr
1
90
6
hr
0
90
10
sec
0
24
hour
4
-50
127
30
°C/°F
1
100
6
sec
0
100
0
min
0
100
0
min
0
100
0
min
0
100
0
min
0
3
-
0
0
1
-
0
0
199
8
hr
0
1
-
0
-50,0
127,0
4,0
°C/°F
1
199
30
min
0
1
0
0
199
0
min
0
1
0
0
15
0
min
0
15
0
hr
0
1
0
0
0
0
°C/°F
-50,0
127,0
-10,0
°C/°F
-50,0
127,0
15,0
°C/°F
A10
200
60
min
-20,0
20,0
2,0
°C/°F
-50,0
150,0
0,0
°C/°F
-50,0
150,0
0,0
°C/°F
0
199
0
min
0
10
5
min
1
100
3
sec
1
100
5
min
1
100
10
min
1
100
5
min
1
100
20
min
0
207
1
0
1
0
1
199
0