Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
CAUTION: To reduce the risk
of damage to the tool, wheel
or brush must not touch guard
when mounted or while in use.
Undetectable damage could occur
to the accessory, causing wires to
fragment from accessory wheel or cup.
MOUNTING WIRE CUP BRUSHES AND WIRE WHEELS
1. Place the tool on a table, guard up.
2. Thread the wheel on the spindle by hand.
3. Depress spindle lock button (c) and use a
wrench on the hub of the wire wheel or brush to
tighten the wheel.
4. To remove the wheel, reverse the above
procedure.
NOTICE: To reduce the risk of damage
to the tool, properly seat the wheel hub
before turning the tool on.
Mounting Cutting (Type 1) Wheels
Cutting wheels include diamond wheels and
abrasive discs. Abrasive cutting wheels for metal
and concrete use are available. Diamond blades
for concrete cutting can also be used. These
accessories are available at extra cost from your
local dealer or authorised service center.
WARNING: A closed, two-sided cutting
wheel guard is re quired when using
cutting wheels. These accessories are
available at extra cost from your local
dealer or authorised service center.
Fail ure to use proper flange and guard
can re sult in injury resulting from wheel
breakage and wheel contact. Please
refer to the Grinding and Cutting
Accessory Chart at the end of this
section to see other accessories that
can be used with these grinders.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
MOUNTING CLOSED (TYPE 1) GUARD (FIG. 5)
1. Open the guard latch (k), and align the lugs (l)
on the guard with the slots on the gear case
(m). This will align the lugs with slots on the gear
case cover. Position the guard facing backward.
2. Push the guard down until the guard lug
engages and rotates freely in the groove on the
gear case hub.
3. Rotate guard (i) into desired working position.
The guard body should be positioned between
the spindle and the operator to provide
maximum operator protection.
4. Close the guard latch to secure the guard on
the gear case cover. You should be unable to
rotate the guard by hand when the latch is in
closed position. Do not operate grinder with a
loose guard or clamp lever in open position.
5. To remove the guard, open the guard latch,
rotate the guard so that the arrows are aligned
and pull up on the guard.
NOTE: The guard is pre-adjusted to the dia met er of
the gear case hub at the factory. If, after a period of
time, the guard becomes loose, tighten the adjusting
screw (n) with the clamp lever in the closed position
with guard installed on the tool.
NOTICE: To reduce the risk of
damage to the tool, do not tighten
adjusting screw (n) with clamp lever in
open position. Undetectable damage to
guard or mounting hub may result.
MOUNTING CUTTING WHEELS (FIG. 1, 4)
CAUTION: Matching diameter backing
flange and clamp nut (included with
tool) must be used for cutting wheels.
1. Place the unthreaded backing flange on
spindle with the raised centre facing up. The
raised centre on the backing flange will be
against the wheel when the wheel is installed.
2. Place the wheel on the backing flange,
centering the wheel on the raised centre.
3. Install the threaded clamp nut with the raised
centre away from the wheel.
4. Depress the spindle lock button (c) and tighten
clamp nut with a wrench.
5. To remove the wheel, depress the spindle lock
button and loosen the threaded clamp nut with
a wrench.
Prior to Operation
• Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.
• Be sure the inner and outer flanges are
mounted correctly.
• Make sure the disc or wheel rotates in the
direction of the arrows on the accessory and
the tool.
ENGLISH
55
Werbung
Inhaltsverzeichnis
